Sorry I meant to say I unplugged P1. El mié., 6 may. 2020 09:00, Leonardo Marsaglia <[email protected]> escribió:
> Well I just checked things with halscope and some keys are working > perfectly but others are not. > > Another problem I find is that matrix_kb is always sensing row 3/col 1 as > true. I unplugged the connector from the P2 port on the 7i73 and the same > happens. I have firmware number 14 installed on the board. Jumpers are ok > for 8x8 matrix (w5 up and w6 down). > > Should I upgrade the firmware just to check ? > > What I find strange is that halscope is detecting the change in the > keycode pin. > > Leonardo Marsaglia > > El mar., 5 may. 2020 22:56, Peter C. Wallace <[email protected]> escribió: > >> On Tue, 5 May 2020, Leonardo Marsaglia wrote: >> >> > Date: Tue, 5 May 2020 22:11:11 -0300 >> > From: Leonardo Marsaglia <[email protected]> >> > Reply-To: "Enhanced Machine Controller (EMC)" >> > <[email protected]> >> > To: "Enhanced Machine Controller (EMC)" < >> [email protected]> >> > Subject: Re: [Emc-users] Mesa 7i73 keypad question/issue >> > >> > Thank you Peter for your quick response, >> >> So if I understand correctly, the 7i73.keycode pin is too fast to simply >> check it with halmeter by eye. But should I see the changes in halscope? >> >> >> Yes halscope will see any changes >> >> >> El mar., 5 may. 2020 a las 19:41, Peter C. Wallace (<[email protected]>) >> escribiяя: >> >> > On Tue, 5 May 2020, Leonardo Marsaglia wrote: >> > >> > > Date: Tue, 5 May 2020 19:09:29 -0300 >> > > From: Leonardo Marsaglia <[email protected]> >> > > Reply-To: "Enhanced Machine Controller (EMC)" >> > > <[email protected]> >> > > To: "Enhanced Machine Controller (EMC)" < >> [email protected] >> > > >> > > Subject: [Emc-users] Mesa 7i73 keypad question/issue >> > > >> > > Hello guys, >> > > >> > > I'm almost done with the config on the Mazak. The last thing I'm >> trying >> > to >> > > set up is the front panel keyboard. I'm using a 7i73 wich is already >> > > working with the MPG and the lever to move the X and Z axis. >> > > >> > > The problem I have is, I can't make the keypad input to work. In HAL >> I'm >> > > always reading the 64 value . I've tried to manually short the pins of >> > one >> > > column and one row to see if there's any change and nothing. I'm sure >> I'm >> > > missing something something here, but I didn't want to experiment >> without >> > > your opinion. >> > > >> > > I don't know If I'm forgetting to ground something, or to move a >> jumper. >> > > Anyway, the P2 port of the board is working well. Please let me know >> what >> > > you think. >> > > >> > > Thanks as always! >> > > >> > >> > You cannot in general use the keycode as it only reports deltas (and >> only >> > for 1 >> > servo thread period) and a no-op code of 64 when idle (no changes) so >> you >> > will >> > miss the deltas in hal watch. Normally tye "matrix_kb" component is used >> > to >> > process the deltas into a static representaion of the keypad state >> > >> > >> > > _______________________________________________ >> > > Emc-users mailing list >> > > [email protected] >> > > https://lists.sourceforge.net/lists/listinfo/emc-users >> > > >> > >> > Peter Wallace >> > Mesa Electronics >> > >> > (\__/) >> > (='.'=) This is Bunny. Copy and paste bunny into your >> > (")_(") signature to help him gain world domination. >> > >> > >> > >> > _______________________________________________ >> > Emc-users mailing list >> > [email protected] >> > https://lists.sourceforge.net/lists/listinfo/emc-users >> > >> >> _______________________________________________ >> Emc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> Peter Wallace >> Mesa Electronics >> >> (\__/) >> (='.'=) This is Bunny. Copy and paste bunny into your >> (")_(") signature to help him gain world domination. >> _______________________________________________ >> Emc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
