Per Tim's suggestion, I upgraded the firmware- problem fixed. Thanks Tim.
Richard, WU5K -----Original Message----- From: FireBrick [mailto:[EMAIL PROTECTED] Sent: Wednesday, November 07, 2007 12:22 PM To: Richard Stouffer; 'FlexRadio List' Subject: Re: [Flexradio] Almost have Flex & PWSDR the way I want Same here Heil ProSet, and Heil Pedal into Heil Yaesu style connector via mic connector on front of Radio. Also a pushbutton into PTT on rear of radio. ----- Original Message ----- From: "Richard Stouffer" <[EMAIL PROTECTED]> To: "'FireBrick'" <[EMAIL PROTECTED]>; "'FlexRadio List'" <flexradio@flex-radio.biz> Sent: Wednesday, November 07, 2007 9:18 AM Subject: RE: [Flexradio] Almost have Flex & PWSDR the way I want >I have had something similar. I'm using a Heil pedal plugged into the >Yeasu > connector assembly for my Heil headset. I'm using the front panel jack. > When > pushed, the PTT turns transmit on, but I can't shut the transmit off and > have to shut SDR down to stop transmitting. I have the problem with and > without the amp. > > Be reminded that I still have a problem with an echo on my headset > whenever > MON is active. Maybe it's RFI. > > Richard, WU5K > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of FireBrick > Sent: Wednesday, November 07, 2007 8:51 AM > To: FlexRadio List > Subject: [Flexradio] Almost have Flex & PWSDR the way I want > > I have one small problem. > > Apparently I'm getting rf into the ptt circuit. > Even though I've torroid the cables properly. > Have a good 'single point ground' > > Operating high power, will cause the ptt footswitch, desk button, and ptt > from my MFJ DVK to stop working. > Problem does not happen at normal barefoot (100watt) levels. > So far, I've experienced this on 80 and 20 meters. > I tend to stay barefoot so haven't had the chance to challenge other > bands/modes to see if they are effected also. > > I must power down the Flex5K and restart. Just shutting down PWSDR won't > fix > > it. > > > I must use VOX instead of manually asserting ptt or having the DVK assert > ptt for me. > I normally only use the ptt footswitch during SSB but ocasionally on cw > just > > so the relays don't work so hard. > > I'm very experienced at solving rfi problems but this one has me stumped. > > If anyone has experienced rfi disabling the ptt circuit and has a > suggestion. > I'm eager to hear it. > > as always > pse & tu > > > ----------------------------------------------------- > I wished the buck stopped here, as I could use a few. > ----------------------------------------------------- > > Bill H. in Chicagoland > webcams at http://76.16.160.118:8080/ > weather at http://hhweather.webhop.org > > > _______________________________________________ > FlexRadio mailing list > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > FlexRadio Knowledge Base: http://kb.flex-radio.com/ > FlexRadio Homepage: http://www.flex-radio.com/ > > > _______________________________________________ FlexRadio mailing list FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ FlexRadio Knowledge Base: http://kb.flex-radio.com/ FlexRadio Homepage: http://www.flex-radio.com/