I have had some good luck with Ham Radio DeLuxe and DM780. I was able to set up SSTV quickly and use it to transmit and receive on 20 meters.
I have had less than good luck in decoding CW, such as the ARRL bulletins on 20 meters. I'd like to find some better answers about this. I have XP-Pro, not Vista. Art Gartner wrote: > Ross, > > Yes, it seems slow. Lately however I'm not changing freq, I'm just seeing > how long it lasts until it quits. > > Art, KA4M > > At 02:56 PM 7/5/2008 -0500, Ross Stenberg wrote: >> Art, I have had problems with this as well as a few others with about the >> same configuration. Don't really know what the answer is. I believe >> operation is OK under XP but not Vista. If you change frequency or other >> settings do you find that operation is very sluggish before getting the >> error? >> >> 73 Ross K9COX >> >> -----Original Message----- >> From: [EMAIL PROTECTED] >> [mailto:[EMAIL PROTECTED] On Behalf Of Art Gartner >> Sent: Saturday, July 05, 2008 2:40 PM >> To: [email protected] >> Subject: [Flexradio] Ham Radio Deluxe and PowerSDR/Flex5000A >> >> I have a problem when trying to run Ham Radio Deluxe with PowerSDR on my >> Flex5000. I'm using N8VB VCOM for com ports. I bring up PowerSDR then HDR. >> I make the connection from HDR and see the frequency and other parameters >> in the HDR screen. Everything is working fine. After about two minutes (can >> be longer) I get an error message from PowerSDR saying "Setup error. Failed >> to load resources from resource file. Please check your setup." I then get >> an error message from HDR that the connection has stopped. When I click >> "OK" on the PowerSDR error message PowerSDR closes. I then close HDR. I >> cannot bring PowerSDR back up without rebooting the computer. Here are the >> operating conditions. >> >> Running Vista on an ASUS Maximus Extreme motherboard. Intel X9650 processor >> (quad 3.0 gHz processors.) 2 gigs of DDR3 RAM, Firewire PCI card using the >> Agere chip. The onboard firewire is disabled in the BIOS. >> >> PowerSDR 1.12.0, Firmware 1.2.0.3. Ham Radio Deluxe V4.0 SP3 build 1875 >> Driver is 3.0.0.70. Running 192 kHz with a 2048 buffer, Safe Mode 1. >> >> N8VB VCOM with four pairs 6 to 16, 7 to 17, 8 to 18, 9 to 19 >> >> In the HDR connection and PowerSDR CAT screen I started out with com 6 to >> 16. Switched to com 8 to 18, no change. I have tried many different >> matching baud rates plus the original 115,000 to 57,600. No change. The ID >> on the CAT setup in PowerSDR is "PowerSDR" the connection in HRD is >> "SDR1000". I changed both to TS-2000, no change. >> >> I have uninstalled PowerSDR, deleted the database and reinstalled PowerSDR. >> No change. I have uninstalled VCOM. I configured it, saved the config and >> installed it again. No change. >> >> My Flex5000A runs fine by itself. As soon as I bring up HRD and make the >> connection PowerSDR goes belly up about 2 minutes later. I'm stumped. >> >> Art, KA4M >> -- Regards, TOM BLACKWELL, PO Box 25403, Dallas, Texas 75225 _______________________________________________ FlexRadio Systems Mailing List [email protected] http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
