See my comments in-line below -Tim
-----Original Message----- From: Paul Radge [mailto:pra...@tpg.com.au] Sent: Sunday, April 19, 2009 11:58 PM To: Tim Ellison; Flex Radio Subject: [SPAM] Re: [SPAM] [Flexradio] sdr1000 + wsjt + edirol fa-66,,,your set up please ? Hi Tim, looking for more feedback please. Microsoft have sent me the hotifx,,,,where should i unzip this file to ,,??? [Tim] Unzip it anywhere. There should be instructions on how to install it; usually by running an executable how can i tell the firewire card is running at 400 or 100 ???? [Tim] This is a great mystery. You really can't know for sure. I have not found a way to test a Firewire connection re IRQ's,,,,my system info won't open,,,i've turned everything back on that i disable to trim XP yet no info to see IRQ's just the egg timer and then nothing,,,,device manager tells me it's on 19 though.Have you any idea how i can get sys info to go again ??? [Tim] This could be indicative of something terribly amiss with your installation of Windows when standard components, such as "System Information" doesn't enumerate hardware device properly. My brain is a little pickled at the moment ,,is there a link to setting up wsjt with the sdr1k and the edirol please,,,??? [Tim], no not specifically for that configuration, but you shouldn't need a specific procedure for that specific hardware if things are working correctly. In general to all,,,,, i've had no feedback from anyone running SDR1K and WSJT and Edirol with their settings ,,,still hoping for some info there please .... regards Paul vk3ddu I assume you are running Windows XP If you haven't done so, look at the Firewire optimization recommendations. http://kc.flex-radio.com/KnowledgebaseArticle50013.aspx Along with the updates if needed http://kc.flex-radio.com/KnowledgebaseArticle50281.aspx -Tim -----Original Message----- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Paul Radge Sent: Sunday, April 19, 2009 8:41 AM To: Flex Radio Subject: [SPAM] [Flexradio] sdr1000 + wsjt + edirol fa-66,,,your set up please ? Hi all, i've upgraded to the Edirol with Sunix firewire card recomended from the knowledge base,,,, I've followed the pdf instructions on th equick start guide,,as per these instructions the tx audio pops and clicks even worse than before. Could someone that is running WSJT on a SDR1000 with the Edirol please send me their set up details,,,,including; Edirol control panel setting VAC 4.09 (bought my own incase the other was corrupt) PSDR either V1.16.1 OR v1.16.2,,Audio primary and VAC WSJT ,,,audio in ,,audio out settings Roman are you still out there my friend ?? (Worth noting my Edirol would not power off the Bus ,,,,a fresh brand new dual core will be next) Onwards Paul vk3ddu please note my VK3DDU email is down and if you wish to email directly pra...@tpg.com.au _______________________________________________ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ _______________________________________________ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/