yes Jim however i do not see anywhere how to set it correct again on ssb i set it to 20Ms and no issue however it will be nice to hear if flex have any info on what is the best number of setting , some say nothing 0ms some say 50ms some say 100ms so whatis the right number ??? thank you for the input jimBTW your one is 100ms ????
vy 73 E.P g0uut /dl9fcc From: Jim Jannuzzo <jsqu...@msn.com> To: paimg0...@btinternet.com; f...@sgsterling.com; flexradio@flex-radio.biz Sent: Thursday, 19 April 2012, 19:26 Subject: RE: [Flexradio] Delay MS is for ?????5000a buffer +acom 1000 If you're on SSB or digital, a long delay of 100 ms doesn't hurt at all. If you're a CW op, then the TX delay adds to the existing latencies. For CW, you should try to keep it as short as possible. The Acom is such a good amp, I bet it protects itself from hot-switching. > Date: Thu, 19 Apr 2012 19:05:57 +0100 > From: paimg0...@btinternet.com > To: f...@sgsterling.com; flexradio@flex-radio.biz > Subject: Re: [Flexradio] Delay MS is for ?????5000a buffer +acom 1000 > > hello Steve > thank you for the info i use 20ms with the Acom 1000 , and no isse however > what is the safe > way to put 50ms 60ms there is no info of what do you think > many thanks > > vy 73 > E.P g0uut > > > > > From: Steve Sterling <f...@sgsterling.com> > To: flexradio@flex-radio.biz > Sent: Thursday, 19 April 2012, 17:02 > Subject: Re: [Flexradio] Delay MS is for ?????5000a buffer +acom 1000 > > Paim-- I will try. > There are three separate lines for keying amplifiers or other equipment on > the back of the Flex 5000. > > For each line, the application of RF power from the Flex may be delayed by > the ms setting. That is, the amp line is keyed, then there is the ms delay > before RF power is applied to the amplifier. > > I use it with my Ameritron solid-state amp. If RF is applied to the input of > the amplifier at the same time as the amplifier line is keyed, I will receive > a fault trip on the amp as it is keyed. By applying a 50ms delay, the amp is > switched into transmit mode via the keying line first without drive power > applied, then 50 ms later RF drive is allowed and the amp is happy. > > Steve WA7DUH > Richland, WA USA > > On 4/19/2012 2:35 AM, paim wrote: > > hi > > is any one can tell me what is the Delay Ms on the antenna section on the > > top for i look on the > > manual and on the net but i do not understand this i use flex 5000a with > > Acom 1000 and in between > > Buffer i set it to 20ms on the delay it is working i was just wondering if > > some one can explain this Delay many thanks . > > vy 73 > > E.P g0uut > > _______________________________________________ > > FlexRadio Systems Mailing List > > FlexRadio@flex-radio.biz > > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > > Knowledge Base: http://kc.flexradio.com/ Homepage: > > http://www.flexradio.com/ > > > _______________________________________________ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ > _______________________________________________ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ _______________________________________________ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/