I got mine to work by checking BOTH "Enable VAC1" on the left and "Output to
VAC" on the right. This is different the PSDR versions before V2.4.4, but it
works.
73, Bruce, W8HW
----- Original Message -----
From: "Bernie Huth" <bh...@garlic.com>
To: "Hunter Mills" <hmills1...@yahoo.com>; <flexradio@flex-radio.biz>
Sent: Monday, September 17, 2012 7:38 PM
Subject: Re: [Flexradio] CW Skimmer - PowerSDR v2.4.4
I could never get it to work. Between the problem with CW Skimmer and the
problem with DXLabs Winwarbler mentioned by Rich, W3ZJ, (below) I reverted
back to Ver. 2.3.5.
---------------
I did have a little trouble with DXLab's WinWarbler because it doesn't like
WDM. But since I feed the power speaker output from the Flex-3000 to the
line input on my computer sound card I was able to configure WinWarbler to
get its audio from the computer sound card instead of the VAC and that seems
to be working OK. I think what we are seeing here is some set up problems
because the Beta testers didn't have duplicates of all our various set ups
but so far it has all been solvable.
73, Rich - W3ZJ
---------------
-73-
Bernie
W4BGH
-------------
on 9/17/12 12:03 PM, Hunter Mills at hmills1...@yahoo.com wrote:
I am having the same problem posted earlier by Bernie, W4BGH, but have not
been
fortunate to find a fix.
I have checked and re-checked my settings in PowerSDR, CSK, and VAC 4.1
but
can't get CSK to decipher.
It was working fine prior to PSDR v2.4.4 upgrade.
Only suggestion I could not try was using FlexRadio, instead of VAC Line
2, as
Signal I/O Device
in CSK. For some reason, Windows XP is not providing that as an audio
device
option (maybe a problem
with my PNP Emulator in XP).
I was using MME in CSK and VAC prior to upgrade but have changed them to
WDMS-K since the upgrade.
Any suggestions would be appreciated - Hunter K3IE.
My setput is the same as Bernie's:
'I am not able to get CW Skimmer v 1.71 to decode properly with PowerSDR
v2.4.4 and a Flex-3000. The radio CAT commands seem to be working
correctly
using PowerSDR v2.4.4
and DXLabs Commander. CW Skimmer is setup as a secondary CAT control in
Commander using Kenwood CAT protocol. The correct frequency is indicated
in
both Commander and CW Skimmer. There is noise indicated in the CW-Skimmer
waterfall, however, there is no
CW decoding indicated. The Audio setup in CW Skimmer is: SoundCard Driver:
WDM
Signal I/O Device: 04 Virtual Cable 2
Audio I/O Device: 03 Virtual Cable 1
Channels: Left/Right: I/Q
Shift Right Channel Data: 0 Samples The Radio setup in CW Skimmer is:
Hardware
Type: SoftRock IF
CW Pitch: 750 Hz
Audio IF: 9750 Hz
Sample Rate: 96 kHz The PowerSDR v2.4.4 VAC setup is: Primary: Buffer
Size:
1024 Sample Rate: 96000 VAC1: Enable VAC1... Checked Driver: Windows
WDM-KS
Input: Virtual Cable 1 Output: Virtual Cable 2 Buffer Size: 1024 Sample
Rate:
96000 Hz Mono/Stereo: unchecked Direct I/Q: checked Calibrate I/Q: checked
Buffer Latency: 120 Allow PTT to override... checked
_______________________________________________
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage:
http://www.flexradio.com/
_______________________________________________
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage:
http://www.flexradio.com/
_______________________________________________
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
