Hello,

You can have a nice read here:

https://puck.nether.net/pipermail/foundry-nsp/2006-December/005382.html

and just for reference the documentation for the commands:

http://www.brocade.com/content/html/en/configuration-guide/NI_05800a_SWITCHING/GUID-04EDFD31-E5FB-4593-8434-0DF8EDB3249E.html

Have a nice day!
--------------------------------------------
On Wed, 5/25/16, Youssef Bengelloun-Zahr <[email protected]> wrote:

 Subject: Re: [f-nsp] MLXe slow on 10G doing inter-vlan routing
 To: "Tudor Capatina" <[email protected]>
 Cc: "[email protected]" <[email protected]>
 Date: Wednesday, May 25, 2016, 12:50 PM
 
 Hello,
 
 Could you please explain the correlation
 between this commands and performance issues observed by the
 OP ?
 
 Best regards.
 
 
 
 2016-05-25 11:06 GMT+02:00
 Tudor Capatina via foundry-nsp <[email protected]>:
 i second
 that,
 
 
 
 no ip icmp redirects - in global config mode or
 
 no ip redirect - in interface config mode
 
 
 
  and you are good to go.
 
 
 
 Tudor
 
 --------------------------------------------
 
 On Wed, 5/25/16, Mike Allen <[email protected]>
 wrote:
 
 
 
  Subject: Re: [f-nsp] MLXe slow on 10G doing inter-vlan
 routing
 
  To: "George B." <[email protected]>
 
  Cc: [email protected]
 
  Date: Wednesday, May 25, 2016, 1:07 AM
 
 
 
  Turn off
 
  ICMP redirects. Common problem in one arm routing
 configs.
 
  IMO it should be the default setting but it's not.
 
  Mike
 
  On May 24, 2016 2:00 PM,
 
  "George B" <[email protected]>
 
  wrote:
 
  Do you notice the same behavior with both UDP and
 
  TCP streams?
 
 
 
 
 
  On Tue, May 24, 2016 at
 
  1:42 PM, Steven Raymond <[email protected]>
 
  wrote:
 
  MLXe,
 
  very lightly loaded, with only one card
 BR-MLX-10Gx8-X. 
 
  Simplest of configuration, layer 2 link with VE
 
  interfaces.  During inter-vlan routing where the
 ingress
 
  traffic and egress traffic are on the same port, say
 e1/2,
 
  the input traffic level will be fine, but the output
 traffic
 
  is effectively maxed out at about 50Mbps (on a 10GigE
 
  port).  Shift hosts around so that the egress is a
 
  different port on the same card, bang problem gone and
 full
 
  expected traffic rates achieved.
 
 
 
 
 
 
 
  Tried numerous code versions, from 05800a to 05900a to
 
  06000.  No improvement.
 
 
 
 
 
 
 
  Of course tried rebooting, new optics, new cabling. 
 No
 
  errors incrementing on the interface.  This is the
 silliest
 
  dumb problem in a long time.  Any ideas are
 appreciated.
 
 
 
 
 
 
 
  Thanks!
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  _______________________________________________
 
 
 
  foundry-nsp mailing list
 
 
 
  [email protected]
 
 
 
  http://puck.nether.net/mailman/listinfo/foundry-nsp
 
 
 
 
 
 
 
 
 
  _______________________________________________
 
 
 
  foundry-nsp mailing list
 
 
 
  [email protected]
 
 
 
  http://puck.nether.net/mailman/listinfo/foundry-nsp
 
 
 
  -----Inline Attachment Follows-----
 
 
 
  _______________________________________________
 
  foundry-nsp mailing list
 
  [email protected]
 
  http://puck.nether.net/mailman/listinfo/foundry-nsp
 
 _______________________________________________
 
 foundry-nsp mailing list
 
 [email protected]
 
 http://puck.nether.net/mailman/listinfo/foundry-nsp
 
 
 -- 
 Youssef
 BENGELLOUN-ZAHR
 
_______________________________________________
foundry-nsp mailing list
[email protected]
http://puck.nether.net/mailman/listinfo/foundry-nsp

Reply via email to