Hello, Indeed, makes a lot more sens now. Thanks for the links.
Best regards. 2016-05-25 12:24 GMT+02:00 Tudor Capatina <[email protected]>: > Hello, > > You can have a nice read here: > > https://puck.nether.net/pipermail/foundry-nsp/2006-December/005382.html > > and just for reference the documentation for the commands: > > > http://www.brocade.com/content/html/en/configuration-guide/NI_05800a_SWITCHING/GUID-04EDFD31-E5FB-4593-8434-0DF8EDB3249E.html > > Have a nice day! > -------------------------------------------- > On Wed, 5/25/16, Youssef Bengelloun-Zahr <[email protected]> wrote: > > Subject: Re: [f-nsp] MLXe slow on 10G doing inter-vlan routing > To: "Tudor Capatina" <[email protected]> > Cc: "[email protected]" <[email protected]> > Date: Wednesday, May 25, 2016, 12:50 PM > > Hello, > > Could you please explain the correlation > between this commands and performance issues observed by the > OP ? > > Best regards. > > > > 2016-05-25 11:06 GMT+02:00 > Tudor Capatina via foundry-nsp <[email protected]>: > i second > that, > > > > no ip icmp redirects - in global config mode or > > no ip redirect - in interface config mode > > > > and you are good to go. > > > > Tudor > > -------------------------------------------- > > On Wed, 5/25/16, Mike Allen <[email protected]> > wrote: > > > > Subject: Re: [f-nsp] MLXe slow on 10G doing inter-vlan > routing > > To: "George B." <[email protected]> > > Cc: [email protected] > > Date: Wednesday, May 25, 2016, 1:07 AM > > > > Turn off > > ICMP redirects. Common problem in one arm routing > configs. > > IMO it should be the default setting but it's not. > > Mike > > On May 24, 2016 2:00 PM, > > "George B" <[email protected]> > > wrote: > > Do you notice the same behavior with both UDP and > > TCP streams? > > > > > > On Tue, May 24, 2016 at > > 1:42 PM, Steven Raymond <[email protected]> > > wrote: > > MLXe, > > very lightly loaded, with only one card > BR-MLX-10Gx8-X. > > Simplest of configuration, layer 2 link with VE > > interfaces. During inter-vlan routing where the > ingress > > traffic and egress traffic are on the same port, say > e1/2, > > the input traffic level will be fine, but the output > traffic > > is effectively maxed out at about 50Mbps (on a 10GigE > > port). Shift hosts around so that the egress is a > > different port on the same card, bang problem gone and > full > > expected traffic rates achieved. > > > > > > > > Tried numerous code versions, from 05800a to 05900a to > > 06000. No improvement. > > > > > > > > Of course tried rebooting, new optics, new cabling. > No > > errors incrementing on the interface. This is the > silliest > > dumb problem in a long time. Any ideas are > appreciated. > > > > > > > > Thanks! > > > > > > > > > > > > > > > > _______________________________________________ > > > > foundry-nsp mailing list > > > > [email protected] > > > > http://puck.nether.net/mailman/listinfo/foundry-nsp > > > > > > > > > > _______________________________________________ > > > > foundry-nsp mailing list > > > > [email protected] > > > > http://puck.nether.net/mailman/listinfo/foundry-nsp > > > > -----Inline Attachment Follows----- > > > > _______________________________________________ > > foundry-nsp mailing list > > [email protected] > > http://puck.nether.net/mailman/listinfo/foundry-nsp > > _______________________________________________ > > foundry-nsp mailing list > > [email protected] > > http://puck.nether.net/mailman/listinfo/foundry-nsp > > > -- > Youssef > BENGELLOUN-ZAHR > > -- Youssef BENGELLOUN-ZAHR
_______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
