The USB drivers are kldloaded. The dmesg output and kernel config aren't included, but available upon request (as is any other config info or other needed data).
Darren Pilgrim wrote:
I have a USB hub that's built into my Viewsonic PT775 monitor. The hub probes during boot and post-boot attach as follows:
uhub1: vendor 0x0543 product 0x00ff, class 9/0, rev 1.00/0.00, addr 2
uhub1: 5 ports with 4 removable, self powered
The hub is connected and disconnected with the switching on and off of the monitor. When the hub is disconnected, whether by unplugging it or turning off the monitor, I get a panic in 4.7p3 if there are no devices connected to the hub's downstream ports. If there are devices connected to the downstream ports, the detach/reattach process works just fine. I only have the one hub to test this issue on. I can't say when the problem appeared as I hadn't used FreeBSD with this hub until a few weeks ago, and I hadn't turned the monitor off with nothing plugged into its USB ports until the 12th. Here is the console output from the panics caused by disconnecting the hub:
Fatal trap 12: page fault while in kernel mode
fault virtual addres = 0x3
fault code = supervisor read, page not present
instruction pointer = 0x8:0xc031fe04
stack pointer = 0x10:0xc0250fb0
frame pointer = 0x10:0xc0250fc4
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = Idle
interrupt mask = bio
trap number = 12
panic: page fault
syncing disks...
Fatal trap 12: page fault while in kernel mode
fault virtual address = 0x30
fault code = supervisor read, page not present
instruction pointer = 0x8:0xc01c2498
stack pointer = 0x10:0xc0250d98
frame pointer = 0x10:0xc0250da0
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = Idle
interrupt mask = bio
trap number = 12
panic: page fault
Later on, when I was testing various configurations and boot/plug/unplug patterns to (try to) fix/diagnose the problem, the debug information was different from the above, but the same for all the panics I induced while testing. This is the output for those panics:
Fatal trap 12: page fault while in kernel mode
fault virtual addres = 0x3
fault code = supervisor read, page not present
instruction pointer = 0x8:0xc031fe04
stack pointer = 0x10:0xc0250fb0
frame pointer = 0x10:0xc0250fc4
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = Idle
interrupt mask = bio
trap number = 12
panic: page fault
syncing disks...
Fatal trap 12: page fault while in kernel mode
fault virtual address = 0x30
fault code = supervisor read, page not present
instruction pointer = 0x8:0xc01c2498
stack pointer = 0x10:0xc0250dd0
frame pointer = 0x10:0xc0250dd8
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = Idle
interrupt mask = bio
trap number = 12
panic: page fault
To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-hackers" in the body of the message
