On Sun, Apr 4, 2010 at 10:32 AM, Kerin Millar <kerfra...@gmail.com> wrote:
> On 04/04/2010 15:20, Mark Knecht wrote:
>>
>> On Sat, Apr 3, 2010 at 7:38 PM, Kerin Millar<kerfra...@gmail.com> wrote:
>>>
>>> On 04/04/2010 02:01, Mark Knecht wrote:
>>>>
>>>> Tried changing root=/dev/md0. No change.
>>>>
>>>> The actual failure message is the fairly standard
>>>>
>>>> VFS - Unable to mount root fs on unknown-block(9,0)
>>>
>>> [snip]
>>>
>>>> CONFIG_MD_RAID1=y
>>>
>>> That's all that needs to be enabled within the RAID section of the
>>> kernel.
>>> However, all the other options that would normally be required to boot
>>> must
>>> also be compiled in statically for things to work as expected (ATA/SCSI
>>> controller driver, filesystem of choice, CONFIG_BLK_DEV_SD and so forth).
>>> It
>>> seems that you may have overlooked something. However, it's impossible to
>>> determine whether that's the case based on the information presented thus
>>> far.
>>>
>>> I would suggest that you double-check your .config in full, or present it
>>> here for review, along with the output of lspci -nn.
>>>
>>> Cheers,
>>>
>>> --Kerin
>>
>> Hi Kerin,
>> Happy for any help I can get.
>>
>> Instead of the whole .config file here's a diff. Remember that the
>> machine already boots non-RAID from /dev/sda and I'm trying to build
>> my first RAID boot on /dev/sdb& sdc.
>>
>
> No, really, the whole thing needs to be seen, along with the lspci data.
> It's very likely that this thread can be drawn to a close if you provide
> exactly what's being asked for :)
>
>> One additional thing I thought of last night was some message that
>> came up when I first built the RAID about the partitions having
>> metadata and to be sure that the bootloader understands metadata. In
>
> The bootloader does not enter into this. If the kernel is being loaded -
> which, by your own admission it is - the bootloader has done its job. What
> happens thereafter is entirely the responsibility of the kernel.
>
> Essentially, the subject of this thread is a misnomer and the issue lies
> with your kernel.
>
> As for the warning regarding metadata, it's applicable to legacy bootloaders
> which may not be able to fathom the presence of the md superblock data at
> the beginning of a block device that happens to be a member of a raid1
> volume. As far as grub is concerned, this is a non-issue. Even if it were an
> issue, you wouldn't even get as far as being able to load the kernel in the
> first instance. Indeed, the bootloader itself would likely fail to
> initialise properly.
>
>> If rebuilding the RAID from scratch is important, or just makes
>> things more straight forward, then don't hesitate to suggest it and
>> I'll document the build step by step. This install isn't important.
>
> On the other hand, if you don't get to the point of understanding why the
> kernel isn't configured so as to be able to assemble the array on this
> occasion, a re-install isn't going to change that. Moreover, you won't be
> able to fix any such problem that may occur again unaided.
>
> Cheers,
>
> --Kerin
No problem supplying it. I did the rebuild this morning but forced
metadata to Type 1.0. No change as you suggested there wouldn't be.
OK, here's:
1) lspci to read & lspci -k to see drivers both from the non-RAID kernel
2) The RAID kernel config
3) At the very end a diff between the kernel config in this email and
the running one without RAID. (I.e. - the changes I made to attempt to
mount / which is on RAID.)
Note that the Marvell SATA controller is for two external eSATA ports
that have nothing attached at this time. It's the Intel controller
that's in play here.
Thanks,
Mark
keeper ~ # lspci
00:00.0 Host bridge: Intel Corporation X58 I/O Hub to ESI Port (rev 13)
00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 1 (rev 13)
00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 3 (rev 13)
00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 7 (rev 13)
00:10.0 PIC: Intel Corporation 5520/5500/X58 Physical and Link Layer
Registers Port 0 (rev 13)
00:10.1 PIC: Intel Corporation 5520/5500/X58 Routing and Protocol
Layer Registers Port 0 (rev 13)
00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management
Registers (rev 13)
00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch
Pad Registers (rev 13)
00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status
and RAS Registers (rev 13)
00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13)
00:19.0 Ethernet controller: Intel Corporation 82567LM-2 Gigabit
Network Connection
00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #4
00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #5
00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #6
00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #2
00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD
Audio Controller
00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 1
00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2
00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 5
00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #1
00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #2
00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #3
00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #1
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90)
00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA
AHCI Controller
00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller
02:00.0 VGA compatible controller: nVidia Corporation G96 [GeForce
9500 GT] (rev a1)
06:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6121 SATA II
Controller (rev b2)
07:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A
IEEE-1394a-2000 Controller (PHY/Link)
keeper ~ #
keeper ~ # lspci -k
00:00.0 Host bridge: Intel Corporation X58 I/O Hub to ESI Port (rev 13)
Subsystem: Intel Corporation Device 4f53
00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 1 (rev 13)
Kernel driver in use: pcieport
00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 3 (rev 13)
Kernel driver in use: pcieport
00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 7 (rev 13)
Kernel driver in use: pcieport
00:10.0 PIC: Intel Corporation 5520/5500/X58 Physical and Link Layer
Registers Port 0 (rev 13)
00:10.1 PIC: Intel Corporation 5520/5500/X58 Routing and Protocol
Layer Registers Port 0 (rev 13)
00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management
Registers (rev 13)
00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch
Pad Registers (rev 13)
00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status
and RAS Registers (rev 13)
00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13)
00:19.0 Ethernet controller: Intel Corporation 82567LM-2 Gigabit
Network Connection
Subsystem: Intel Corporation Device 0000
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #4
Subsystem: Intel Corporation Device 4f53
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #5
Subsystem: Intel Corporation Device 4f53
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #6
Subsystem: Intel Corporation Device 4f53
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #2
Subsystem: Intel Corporation Device 4f53
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD
Audio Controller
Subsystem: Intel Corporation Device 0022
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 1
Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2
Kernel driver in use: pcieport
00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 5
Kernel driver in use: pcieport
00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #1
Subsystem: Intel Corporation Device 4f53
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #2
Subsystem: Intel Corporation Device 4f53
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #3
Subsystem: Intel Corporation Device 4f53
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #1
Subsystem: Intel Corporation Device 4f53
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90)
00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller
Subsystem: Intel Corporation Device 4f53
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA
AHCI Controller
Subsystem: Intel Corporation Device 4f53
Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller
Subsystem: Intel Corporation Device 4f53
02:00.0 VGA compatible controller: nVidia Corporation G96 [GeForce
9500 GT] (rev a1)
Kernel driver in use: nvidia
Kernel modules: nvidia
06:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6121 SATA II
Controller (rev b2)
Subsystem: Intel Corporation Device 4f53
Kernel driver in use: ahci
07:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A
IEEE-1394a-2000 Controller (PHY/Link)
Subsystem: Intel Corporation Device 4f53
Kernel modules: firewire-ohci
keeper ~ #
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_DETECT_HUNG_TASK=y
# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_KMEMLEAK is not set
CONFIG_DEBUG_PREEMPT=y
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_VIRTUAL is not set
# CONFIG_DEBUG_WRITECOUNT is not set
# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_ARCH_WANT_FRAME_POINTERS=y
# CONFIG_FRAME_POINTER is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_USER_STACKTRACE_SUPPORT=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_FP_TEST=y
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set
# CONFIG_FIREWIRE_OHCI_REMOTE_DMA is not set
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
CONFIG_HAVE_ARCH_KMEMCHECK=y
# CONFIG_STRICT_DEVMEM is not set
CONFIG_X86_VERBOSE_BOOTUP=y
CONFIG_EARLY_PRINTK=y
# CONFIG_EARLY_PRINTK_DBGP is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PER_CPU_MAPS is not set
# CONFIG_X86_PTDUMP is not set
CONFIG_DEBUG_RODATA=y
# CONFIG_DEBUG_RODATA_TEST is not set
# CONFIG_DEBUG_NX_TEST is not set
# CONFIG_IOMMU_DEBUG is not set
# CONFIG_IOMMU_STRESS is not set
CONFIG_HAVE_MMIOTRACE_SUPPORT=y
CONFIG_IO_DELAY_TYPE_0X80=0
CONFIG_IO_DELAY_TYPE_0XED=1
CONFIG_IO_DELAY_TYPE_UDELAY=2
CONFIG_IO_DELAY_TYPE_NONE=3
CONFIG_IO_DELAY_0X80=y
# CONFIG_IO_DELAY_0XED is not set
# CONFIG_IO_DELAY_UDELAY is not set
# CONFIG_IO_DELAY_NONE is not set
CONFIG_DEFAULT_IO_DELAY_TYPE=0
# CONFIG_CPA_DEBUG is not set
# CONFIG_OPTIMIZE_INLINING is not set
# CONFIG_DEBUG_STRICT_USER_COPY_CHECKS is not set
#
# Security options
#
# CONFIG_KEYS is not set
CONFIG_SECURITY=y
# CONFIG_SECURITYFS is not set
# CONFIG_SECURITY_NETWORK is not set
# CONFIG_SECURITY_PATH is not set
# CONFIG_SECURITY_TOMOYO is not set
# CONFIG_IMA is not set
# CONFIG_DEFAULT_SECURITY_SELINUX is not set
# CONFIG_DEFAULT_SECURITY_SMACK is not set
# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
CONFIG_DEFAULT_SECURITY_DAC=y
CONFIG_DEFAULT_SECURITY=""
CONFIG_ASYNC_TX_DISABLE_PQ_VAL_DMA=y
CONFIG_ASYNC_TX_DISABLE_XOR_VAL_DMA=y
CONFIG_CRYPTO=y
#
# Crypto core or helper
#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=m
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_BLKCIPHER2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_PCOMP=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
CONFIG_CRYPTO_GF128MUL=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_WORKQUEUE=y
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_AUTHENC=m
CONFIG_CRYPTO_TEST=m
#
# Authenticated Encryption with Associated Data
#
# CONFIG_CRYPTO_CCM is not set
# CONFIG_CRYPTO_GCM is not set
# CONFIG_CRYPTO_SEQIV is not set
#
# Block modes
#
CONFIG_CRYPTO_CBC=y
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
#
# Hash modes
#
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
CONFIG_CRYPTO_CRC32C=y
# CONFIG_CRYPTO_CRC32C_INTEL is not set
# CONFIG_CRYPTO_GHASH is not set
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
# CONFIG_CRYPTO_RMD256 is not set
# CONFIG_CRYPTO_RMD320 is not set
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
# CONFIG_CRYPTO_GHASH_CLMUL_NI_INTEL is not set
#
# Ciphers
#
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_AES_X86_64=m
# CONFIG_CRYPTO_AES_NI_INTEL is not set
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_FCRYPT=m
CONFIG_CRYPTO_KHAZAD=m
# CONFIG_CRYPTO_SALSA20 is not set
CONFIG_CRYPTO_SALSA20_X86_64=m
CONFIG_CRYPTO_SEED=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_TWOFISH_X86_64=m
#
# Compression
#
CONFIG_CRYPTO_DEFLATE=m
# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set
#
# Random Number Generation
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
CONFIG_CRYPTO_HW=y
# CONFIG_CRYPTO_DEV_PADLOCK is not set
# CONFIG_CRYPTO_DEV_HIFN_795X is not set
CONFIG_HAVE_KVM=y
CONFIG_VIRTUALIZATION=y
# CONFIG_KVM is not set
CONFIG_VIRTIO=m
CONFIG_VIRTIO_RING=m
CONFIG_VIRTIO_PCI=m
CONFIG_VIRTIO_BALLOON=m
# CONFIG_BINARY_PRINTF is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_GENERIC_FIND_FIRST_BIT=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_FIND_LAST_BIT=y
CONFIG_CRC_CCITT=m
CONFIG_CRC16=y
# CONFIG_CRC_T10DIF is not set
CONFIG_CRC_ITU_T=y
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_NLATTR=y
keeper ~ #
keeper ~ # diff /usr/src/linux/.config /mnt/gentoo/usr/src/linux/.config
4c4
< # Mon Mar 29 01:02:31 2010
---
> # Sun Apr 4 09:56:49 2010
893,912c893,906
< CONFIG_MD_LINEAR=m
< CONFIG_MD_RAID0=m
< CONFIG_MD_RAID1=m
< CONFIG_MD_RAID10=m
< CONFIG_MD_RAID456=m
< # CONFIG_MULTICORE_RAID456 is not set
< CONFIG_MD_RAID6_PQ=m
< # CONFIG_ASYNC_RAID6_TEST is not set
< CONFIG_MD_MULTIPATH=m
< CONFIG_MD_FAULTY=m
< CONFIG_BLK_DEV_DM=m
< CONFIG_DM_DEBUG=y
< CONFIG_DM_CRYPT=m
< CONFIG_DM_SNAPSHOT=m
< CONFIG_DM_MIRROR=m
< # CONFIG_DM_LOG_USERSPACE is not set
< CONFIG_DM_ZERO=m
< CONFIG_DM_MULTIPATH=m
< # CONFIG_DM_MULTIPATH_QL is not set
< # CONFIG_DM_MULTIPATH_ST is not set
---
> # CONFIG_MD_LINEAR is not set
> CONFIG_MD_RAID0=y
> CONFIG_MD_RAID1=y
> # CONFIG_MD_RAID10 is not set
> # CONFIG_MD_RAID456 is not set
> # CONFIG_MD_MULTIPATH is not set
> # CONFIG_MD_FAULTY is not set
> CONFIG_BLK_DEV_DM=y
> # CONFIG_DM_DEBUG is not set
> # CONFIG_DM_CRYPT is not set
> # CONFIG_DM_SNAPSHOT is not set
> # CONFIG_DM_MIRROR is not set
> # CONFIG_DM_ZERO is not set
> # CONFIG_DM_MULTIPATH is not set
914,915c908,909
< CONFIG_DM_UEVENT=y
< CONFIG_BLK_DEV_DM_BBR=m
---
> # CONFIG_DM_UEVENT is not set
> # CONFIG_BLK_DEV_DM_BBR is not set
2293,2298d2286
< CONFIG_XOR_BLOCKS=m
< CONFIG_ASYNC_CORE=m
< CONFIG_ASYNC_MEMCPY=m
< CONFIG_ASYNC_XOR=m
< CONFIG_ASYNC_PQ=m
< CONFIG_ASYNC_RAID6_RECOV=m
keeper ~ #
