Stefan G. Weichinger:
> On an older server the customer replaced a SAS drive.
>
> I see it as /dev/sg11, but not yes as /dev/sdX, it is not visible in "lsblk"
...
Not that I think it will help you much, but there is sys-apps/sg3_utils:
# lsscsi
[0:0:0:0] disk ATA TOSHIBA MG03ACA3 FL1A /dev/sda
[1:0:0:0] disk ATA TOSHIBA MG03ACA3 FL1A /dev/sdb
[5:0:0:0] cd/dvd ASUS DRW-24F1ST a 1.00 /dev/scd0
# sg_map -x -i
/dev/sg0 0 0 0 0 0 /dev/sda ATA TOSHIBA MG03ACA3 FL1A
/dev/sg1 1 0 0 0 0 /dev/sdb ATA TOSHIBA MG03ACA3 FL1A
/dev/sg2 5 0 0 0 5 /dev/scd0 ASUS DRW-24F1ST a 1.00
# sg_inq /dev/sg1
standard INQUIRY:
PQual=0 Device_type=0 RMB=0 LU_CONG=0 version=0x05 [SPC-3]
[AERC=0] [TrmTsk=0] NormACA=0 HiSUP=0 Resp_data_format=2
SCCS=0 ACC=0 TPGS=0 3PC=0 Protect=0 [BQue=0]
EncServ=0 MultiP=0 [MChngr=0] [ACKREQQ=0] Addr16=0
[RelAdr=0] WBus16=0 Sync=0 [Linked=0] [TranDis=0] CmdQue=1
[SPI: Clocking=0x0 QAS=0 IUS=0]
length=96 (0x60) Peripheral device type: disk
Vendor identification: ATA
Product identification: TOSHIBA MG03ACA3
Product revision level: FL1A
Unit serial number: 14UAKBPDF
You have theese two:
> 07:01.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X
> 0a:0e.0 RAID bus controller: Adaptec AAC-RAID
I guess that the tape drive and mediachanger is on the 53c1030:
> [0:0:1:0] tape HP Ultrium 4-SCSI B12H /dev/st0
> [0:0:1:1] mediumx OVERLAND NEO Series 0510 /dev/sch0
And theese on the aac, since they have the same scsi host, and I guess
that scsi ch.0 is for the configured drives and ch.1 for the raw drives:
> [1:0:1:0] disk ICP SAS2 V1.0 /dev/sda
> [1:0:2:0] disk ICP Device 2 V1.0 /dev/sdb
> [1:0:3:0] disk ICP Device 3 V1.0 /dev/sdc
> [1:0:4:0] disk ICP Device 4 V1.0 /dev/sdd
> [1:0:5:0] disk ICP Device 5 V1.0 /dev/sde
> [1:0:6:0] disk ICP Device 6 V1.0 /dev/sdf
> [1:0:7:0] disk ICP Device 7 V1.0 /dev/sdg
> [1:0:8:0] disk ICP Device 8 V1.0 /dev/sdh
> [1:0:9:0] disk ICP Device 9 V1.0 /dev/sdi
> [1:1:0:0] disk TOSHIBA MG04SCA20EE 0104
> [1:1:1:0] disk SEAGATE ST373455SS 0002 -
> [1:1:3:0] disk WDC WD7500AZEX-00RKK 0A80 -
> [1:1:4:0] disk WDC WD7500AZEX-00RKK 0A80 -
> [1:1:5:0] disk WDC WD7500AZEX-00RKK 0A80 -
> [1:1:6:0] disk WDC WD7500AZEX-00BN5 1A01 -
> [1:1:7:0] disk WDC WD7500AZEX-00BN5 1A01 -
> [1:1:8:0] disk WDC WD7500AZEX-00RKK 0A80 -
> [1:1:9:0] disk ST375052 8AS CC44 -
> [1:1:10:0] disk WDC WD7500AZEX-00BN5 1A01 -
> [1:1:11:0] disk WDC WD7500AZEX-00BN5 1A01 -
Perhaps theese links will help:
https://www.cyberciti.biz/faq/linux-checking-sas-sata-disks-behind-adaptec-raid-controllers/
http://updates.aslab.com/doc/disk-controller/aacraid_guide.pdf
https://hwraid.le-vert.net/wiki/Adaptec
Just a poke in the dark, does ldd report all libs found, as in:
$ ldd /bin/ls
linux-vdso.so.1 (0x00007ffcbab4c000)
libc.so.6 => /lib64/libc.so.6 (0x00007fece3ad5000)
/lib64/ld-linux-x86-64.so.2 (0x00007fece3d1c000)
$
Regards,
/Karl Hammar
