Hello, I have created a LDS, Its the main catalog volume where I have created this COMMDS,ACDS,SCDS. I was able to bring up the system but when I try to use ISMF 8.3 to alter the base configuration i get the CDS is not found though it is very much visible via D SMS,OPTIONS and when i do SETSMS COMMDS(SYSTEM.ZT01.COMMDS), I get the below information.
IEE600I REPLY TO 011 IS;U IGD056I COMMDS SYSTEM.ZT01.COMMDS NOT FOUND Not sure where is it exactly missing on.. On Thu, Oct 10, 2013 at 2:59 AM, Lizette Koehler <stars...@mindspring.com>wrote: > You cannot activate an already active ACDS SCDS or COMMDS. They would > need > to be new to do that. > > You seem to have a valid ACDS and SCDS in the configuration. If I > understand your current issue it is the COMMDS. > > So I have some basic questions. > > When it was defined, you created a Linear VSAM Dataset? > It is on a volume that is accessible to your LPAR? > > When the SYSTEM IPLd, you indicated it could not use the COMMDS, but it > could use the SCDS and ACDS? > What happens when you issue the SETSMS COMMDS(your.data.set.name.here) > > Provide all messages. > > Is all that correct? > > Lizette > > > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] On > Behalf Of mf db > Sent: Wednesday, October 09, 2013 1:42 PM > To: IBM-MAIN@LISTSERV.UA.EDU > Subject: Re: NO COMMUNICATIONS DATA SET - IGD002I > > Hello Lizette, > > I did for SETSMS for COMMDS there was no response at all, but for SCDS and > ACDS i got the below : > > setsms acds(system.zt01.acds) > IGD068I ACDS SYSTEM.ZT01.ACDS SPECIFIED IS THE SAME AS THE ACTIVE ACDS > - COMMAND IS REJECTED > > > setsms scds(system.zt01.scds) > IGD056I ACDS SYSTEM.ZT01.ACDS NOT FOUND > IGD052I REQUEST DENIED - NO ACTIVE CONFIGURATION > > > On Thu, Oct 10, 2013 at 1:58 AM, Lizette Koehler > <stars...@mindspring.com>wrote: > > > If he did a SETSMS COMMDS(SYSTEM.ZT01.COMMDS) and it got an IGD002I > > then something else might be incorrect. > > > > Could you do the SETSMS command and post all message from the invocation? > > > > > > > > Lizette > > > > > > -----Original Message----- > > From: IBM Mainframe Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] > > On Behalf Of Jim Blalock > > Sent: Wednesday, October 09, 2013 1:09 PM > > To: IBM-MAIN@LISTSERV.UA.EDU > > Subject: Re: NO COMMUNICATIONS DATA SET - IGD002I > > > > Is the COMMDS cataloged in the master catalog? SMS may be started > > early enough that the usercats aren't available yet. > > > > On 10/9/2013 3:59 PM, mf db wrote: > > > Lizette, > > > > > > Its during IPL.. but before IPL i did updated the IGDSMS00 with the > > > new ACDS and COMMDS. During IPL it said it couldn't recognize the > > > COMMDS, so I tried activating by SETSMS COMMDS/SETSMS ACDS/SETSMS > > > SCDS > > but > > no luck. > > > > > > d sms,options > > > IGD002I 15:58:40 DISPLAY SMS 613 > > > ACDS = SYSTEM.ZT01.ACDS > > > COMMDS = SYSTEM.ZT01.COMMDS > > > ACDS LEVEL = UNAVAIL > > > > > > > > > > > > On Thu, Oct 10, 2013 at 12:39 AM, Lizette Koehler > > > <stars...@mindspring.com>wrote: > > > > > >> I would also do a D SMS,OPTIONS and check to see if the files are > > >> recognized. > > >> > > >> Lizette > > >> > > >> > > >> -----Original Message----- > > >> From: IBM Mainframe Discussion List > > >> [mailto:IBM-MAIN@LISTSERV.UA.EDU] On Behalf Of Lizette Koehler > > >> Sent: Wednesday, October 09, 2013 12:08 PM > > >> To: IBM-MAIN@LISTSERV.UA.EDU > > >> Subject: Re: NO COMMUNICATIONS DATA SET - IGD002I > > >> > > >> What were you doing at the time? And IPL? A SETSMS? > > >> > > >> How is your IGDSMSxx member created? > > >> > > >> SMS ACDS(dsname) COMMDS(dsname) > > >> > > >> > > >> Try a SETSMS COMMDS(xxxxx) Check my syntax. > > >> > > >> > > >> > > >> Lizette > > >> > > >> > > >> -----Original Message----- > > >> From: IBM Mainframe Discussion List > > >> [mailto:IBM-MAIN@LISTSERV.UA.EDU] On Behalf Of mf db > > >> Sent: Wednesday, October 09, 2013 12:02 PM > > >> To: IBM-MAIN@LISTSERV.UA.EDU > > >> Subject: NO COMMUNICATIONS DATA SET - IGD002I > > >> > > >> Hello Group, > > >> > > >> I am trying to bring up our sandbox for testing purpose, but while > > >> Bring up the I get message as > > >> > > >> IGD002I : NO COMMUNICATIONS DATA SET > > >> > > >> Though i have defined it in IGDSMS00 and Also I did the activate of > > >> SET SMS=xx, but still I do not get this activated during IPL. > > >> > > >> This is a new COMMDS,ACDS,SCDS defined but still I do not see get > > >> clue where I missed on. > > >> > > >> Any suggestions or pointers ? > > >> > > >> Peter > > >> > > > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
