Information I would need at this point is
1) Did you contact CA ACF2 for assistance? They are very helpful and can
probably resolve this issue more quickly.
2) The output of the following IDCAMS lists
LISTC ENT('QWS.SEC.RULES') all
3) Provide the section of SYSLOG where your IKJ message occurs, 10 lines above
and below the message. I am looking for additional IDC, IGD, IEC, etc type
messages.
4) Show us the manual section in the ACF2 manual that states you use a
SHAREOPT(1,3)
5) Did you contact CA ACF2 for assistance.
5) Have you searched the CA Support website to see if there is already a
suggestion for this issue?
You can code a proc in proclib to do step 2. Then issue a S xxxxx and get the
listing. If security is not available, you may not be able to run the job.
The list is great, but if there is this much difficulty, then contacting the
vendor could resolve this issue more quickly.
Lizette
-----Original Message-----
>From: "Steely, Mark" <mark.ste...@hp.com>
>Sent: Aug 27, 2015 6:30 AM
>To: IBM-MAIN@LISTSERV.UA.EDU
>Subject: Re: Catalog entry not visible
>
>I think the VVDS needs to be dump and look at the entry and see if the VVDS
>has the correct catalog listed.
>
>Thanks
>
>-----Original Message-----
>From: IBM Mainframe Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] On
>Behalf Of Nathan Astle
>Sent: Thursday, August 27, 2015 7:49 AM
>To: IBM-MAIN@LISTSERV.UA.EDU
>Subject: Re: Catalog entry not visible
>
>Hi John,
>
>The System is not yet fully up and it is failing at the Security product start
>up. I can see the Catalog services are available.
>
>Nathan
>
>On Thu, Aug 27, 2015 at 6:15 PM, John McKown <john.archie.mck...@gmail.com>
>wrote:
>
>> On Thu, Aug 27, 2015 at 7:36 AM, Andrew Rowley <
>> and...@blackhillsoftware.com
>> > wrote:
>>
>> > Stretching my memory, isn't there something about VSAM files can
>> > only be cataloged in 1 catalog, unless they are SYS1.* datasets? I
>> > think there is some information in the VVDS?
>> >
>>
>> This is correct. There are "special dispensations" for VSAM data sets
>> which start with SYS1. _or_ are PAGESPACE data sets. But, in this
>> case, the VSAM data set in question is said to be in a _shared_
>> catalog. Which is certainly allowed. The OP can "see" it in a 3.4
>> listing on both systems. I don't remember reading what else has been
>> tried. Personally, on the new system, I think that I'd try a simple
>> TSO ALLOCATE of the DSN in my TSO session. I don't recall if the OP
>> has done this or not.
>>
>>
>>
>> >
>> > Regards
>> >
>> > Andrew Rowley
>> >
>> >
>>
>> --
>>
>> Schrodinger's backup: The condition of any backup is unknown until a
>> restore is attempted.
>>
>> Yoda of Borg, we are. Futile, resistance is, yes. Assimilated, you will be.
>>
>> He's about as useful as a wax frying pan.
>>
>> 10 to the 12th power microphones = 1 Megaphone
>>
>> Maranatha! <><
>> John McKown
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
