Terry, >From the SAL screen, there is a PF key to list the files on the CP parm disk. It may help you in determining what went wrong. If you made a backup of the SYSTEM CONFIG on the parm disk, then you can use the FN= and FT= options in the IPL parameters area to point to another SYSTEM CONFIG. If you have another CP parm disk (i.e. 2 or 3) that would work, then there is field in the upper left of the SAL screen where you can point to another CP parm disk. Press enter on the SAL screen to unprotect the CP parm disk field, and press enter after entering a new value.
________________________________ From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On Behalf Of Martin, Terry R. (CMS/CTR) (CTR) Sent: Friday, September 12, 2008 2:49 PM To: IBMVM@LISTSERV.UARK.EDU Subject: Re: WAIT STATE This not the first time I have had this VM up. I changed the system config adding page packs and such and might have had a finger check! Thank You, Terry Martin Lockheed Martin - Information Technology z/OS & z/VM Systems - Performance and Tuning Cell - 443 632-4191 Work - 410 786-0386 [EMAIL PROTECTED] ________________________________ From: Martin, Terry R. (CMS/CTR) (CTR) Sent: Friday, September 12, 2008 4:44 PM To: 'The IBM z/VM Operating System' Subject: RE: WAIT STATE Hi Yes, I found this explanation. I think I might have messed up my system config file which is what is causing this. Can I go into SAPL mode and enter the cons to get me back in the system if the system config is in fact corrupted? Thank You, Terry Martin Lockheed Martin - Information Technology z/OS & z/VM Systems - Performance and Tuning Cell - 443 632-4191 Work - 410 786-0386 [EMAIL PROTECTED] ________________________________ From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On Behalf Of Doug Breneman Sent: Friday, September 12, 2008 4:36 PM To: IBMVM@LISTSERV.UARK.EDU Subject: Re: WAIT STATE HCP1010W NO CONSOLE AVAILABLE. Explanation: The indicated disabled wait state PSW is loaded when an operational primary or alternate operator's console cannot be found. If you were running in virtual mode, CONMODE was not set to 3270. System Action: The system enters a disabled wait state (wait state code = 1010). If using the Stand-Alone Program Loader (SAPL), all registers contain the values held at the time the wait state was entered. Register 2 contains the console device address. Operator Response: There is probably a hardware malfunction. Notify your system support personnel. Verify that the RIOGEN macro instruction properly defined the primary and alternate system consoles. If you were running in virtual mode, enter the TERMinal CONMODE 3270 command, and re-IPL. If using SAPL, either specify the correct console address on the LOADPARM parameter of the IPL command or specify the correct console address using the 'CONS=' IPL parameter on the SAPL menu screen. Refer to Overriding Stand-Alone Program Loader Defaults in z/VM: CP Planning and Administration. If the problem persists, contact your IBM Support Center personnel to diagnose and correct the hardware error. Doug Breneman z/VM Development IBM Endicott Inactive hide details for "Martin, Terry R. (CMS---09/12/2008 04:27:55 PM---Hi"Martin, Terry R. (CMS---09/12/2008 04:27:55 PM---Hi From: "Martin, Terry R. (CMS/CTR) (CTR)" <[EMAIL PROTECTED]> To: IBMVM@LISTSERV.UARK.EDU Date: 09/12/2008 04:27 PM Subject: WAIT STATE ________________________________ Hi I am trying to bring up a new VM LPAR and I am receiving a DISABLED WAIT STATE CODE: 1010. Any ideas? Thank You, Terry Martin Lockheed Martin - Information Technology z/OS & z/VM Systems - Performance and Tuning Cell - 443 632-4191 Work - 410 786-0386 [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
