Dear all, Thank you very much for the many helpful replies to my question! I greatly appreciate the time you have taken to share your suggestions, macros, and plugins.
I am currently working through the different approaches that have been proposed. If I have any further questions, I will get back to the list. Best, Themis Στις Παρ 5 Ιουν 2026 στις 10:03 π.μ., ο/η Michael Schmid < [email protected]> έγραψε: > Hi Themis, > > here is a macro that you could use as a starting point for the example-1 > image. > It is essential to correct for the different brightness-dependent > contrast that is caused by the nonlinear transfer curve (gamma-like) of > a jpg image. The gamma=2 correction is only a rough approximation for > this. A raw or tiff image with no gamma correction (i.e. gamma=1) would > be clearly preferable! > > run("Gamma...", "value=2"); > run("Duplicate...", "title=example_1-background.jpg"); > run("Subtract Background...", "rolling=2 create sliding disable"); > run("Median...", "radius=5"); > imageCalculator("Subtract", "example_1.jpg","example_1-background.jpg"); > > > Michael > ________________________________________________________________ > On 03.06.26 17:58, Moraitou Themis wrote: > > Thank you for your responses. > > > > Unfortunately, the images we have are only available in JPG format. I > have > > attached two files as references for what I described in my previous > posts. > > > > If you have any additional suggestions or comments based on these > examples, > > I would greatly appreciate them. > > > > Best > > > > Themis > > > > Στις Τρί 2 Ιουν 2026 στις 1:35 μ.μ., ο/η Gluender <[email protected]> > έγραψε: > > > >> You wrote: > >> > >> "[...] is there a tool that we can use to select only the fungal hyphae > >> of the emulsion surface?" > >> > >> A tool? > >> There may be methods / approaches to reduce the impact of image > >> artifacts and to more or less isolate the structures of interest but, as > >> mentioned before, without typical images, I see no way to provide > >> substantial help. > >> > >> Good luck > >> > >> Herbie > >> > >> ::::::::::::::::::::::::::::::::::::::::::::: > >> Am 02.06.26 um 14:26 schrieb Moraitou Themis: > >>> Thank you very much Herbie! > >>> > >>> Just one more question... > >>> Since our images have been taken using transmitted light, and the > surface > >>> of a photographic slide is never absolutely clean (there are always > >> surface > >>> deposits/dust, scratches etc), is there a tool that we can use to > select > >>> only the fungal hyphae of the emulsion surface? > >>> > >>> Best > >>> Themis > >>> > >>> Στις Τρί 2 Ιουν 2026 στις 10:48 π.μ., ο/η Gluender <[email protected]> > >>> έγραψε: > >>> > >>>> Greetings Moraitou Themis! > >>>> > >>>> Without seeing typical images in their original non-lossy file-format > >>>> (no JPGs, no screen-shots) it is near to impossible to help. > >>>> > >>>> "What would be the best approach to improve the separation of hyphae > >> from > >>>> the background before thresholding?" > >>>> > >>>> Frankly speaking: > >>>> The best pre-processing is no pre-processing but better images. > >>>> > >>>> You may try to improve image acquisition by using color lighting for > >>>> better contrast. Phase contrast may also be of some help. Avoid > >>>> "structures or artifacts are present in the image", etc. > >>>> > >>>> Best > >>>> > >>>> Herbie > >>>> > >>>> ::::::::::::::::::::::::::::::::::::::::::::: > >>>> Am 02.06.26 um 11:29 schrieb Moraitou Themis: > >>>>> Dear all, > >>>>> > >>>>> I am interested in quantifying fungal hyphae growth on the surface of > >>>>> photographic color slides using images taken with a Dino-Lite > >> microscope. > >>>>> > >>>>> The basic workflow that I follow in ImageJ roughly includes: > >>>>> > >>>>> 1. Convert the image to 8-bit grayscale. > >>>>> 2. Apply Subtract Background. > >>>>> 3. Use automatic thresholding (Otsu and Li seem to give the best > >> results > >>>> so > >>>>> far). > >>>>> > >>>>> However, I encounter two main issues: > >>>>> > >>>>> - The background is not uniform, and some structures or artifacts are > >>>>> present in the image. As a result, background subtraction is often > not > >>>>> sufficient to isolate the hyphae. > >>>>> - In some regions, the contrast between the hyphae and the background > >> is > >>>>> too low, so the threshold does not detect all hyphae consistently. > >>>>> > >>>>> What would be the best approach to improve the separation of hyphae > >> from > >>>>> the background before thresholding? Are there specific preprocessing > >>>> steps, > >>>>> filters, color-space transformations, or segmentation methods in > >>>>> ImageJ/Fiji that could help achieve more reliable detection and > >>>>> quantification? > >>>>> > >>>>> Any suggestions or examples of similar workflows would be greatly > >>>>> appreciated. > >>>>> > >>>>> Thank you! > >>>>> > >>>>> -- > >>>>> ImageJ mailing list: http://imagej.nih.gov/ij/list.html > >>>>> > >>>> > >>>> -- > >>>> ImageJ mailing list: http://imagej.nih.gov/ij/list.html > >>>> > >>> > >>> > >> > >> -- > >> ImageJ mailing list: http://imagej.nih.gov/ij/list.html > >> > > > > -- > > ImageJ mailing list: http://imagej.nih.gov/ij/list.html > > -- > ImageJ mailing list: http://imagej.nih.gov/ij/list.html > -- *Efthymia (Themis) Moraitou, PhD* Conservation of Antiquities & Works of Art Cultural Informatics & Communication -- ImageJ mailing list: http://imagej.nih.gov/ij/list.html
