> Simon,
>
> Have a look for the file i2c-id.h and check it has the variable
>
> I2C_HW_B_CX2341X set. You might have more than one version of this file on
> your system. Check to see lirc is using the right one because if the
> variable is not in the file lirc will compile the code without the wrong
> probe structure.
There seems to be a few versions of the file:
/usr/include/linux/i2c-id.h
/usr/src/kernels/linux-2.6.16.18/include/linux/i2c-id.h
/lib/modules/2.6.16.18/build/include/linux/i2c-id.h (system link)
grep I2C_HW_B_CX2341X
/usr/src/kernels/linux-2.6.16.18/include/linux/i2c-id.h
<nothing>
grep I2C_HW_B_CX2341X /usr/include/linux/i2c-id.h
<nothing>
Hans had said for my <2.6.17 kernel (2.6.16.18), I2C_HW_B_CX2341X isn't
used?? I2C_HW_B_BT848 is used instead, which is defined:
#define I2C_HW_B_BT848 0x05 /* BT848 video boards */
Could you send me a grep of your i2c-id.h for I2C_HW_B_CX2341X ??
Thanks!
> Simon Baxter schreef:
>>> $ diff lirc/drivers/lirc_i2c/lirc_i2c.c lirc\
>>> 062106/drivers/lirc_i2c/lirc_i2c.c
>>> < /* $Id: lirc_i2c.c,v 1.38 2006/06/26 23:21:34 lirc Exp $ */
>>>
>>>> /* $Id: lirc_i2c.c,v 1.37 2006/05/20 04:38:58 lirc Exp $ */
>>>>
>>> < #ifdef I2C_HW_B_CX2341X
>>> < if (adap->id == (I2C_ALGO_BIT | I2C_HW_B_BT848) ||
>>> < adap->id == (I2C_ALGO_BIT | I2C_HW_B_CX2341X))
>>> < #else
>>> < if (adap->id == (I2C_ALGO_BIT | I2C_HW_B_BT848))
>>> < #endif
>>> < {
>>> ---
>>>
>>>> if (adap->id == (I2C_ALGO_BIT | I2C_HW_B_BT848)) {
>>>>
>>> Seems to have added some checking for i2c definitions for
>>> I2C_HW_B_CX2341X
>>> (kernel 2.6.17+) and I2C_HW_B_BT848. Certainly looks like some updates
>>> in
>>> the right areas, but proof will be in the pudding!
>>>
>>> Will try it tonight....
>>>
>>
>>
>> There must be something fundamental I'm doing wrong. I get the same
>> problem:
>>
>> 1010 cvs -d:pserver:[EMAIL PROTECTED]:/cvsroot/lirc
>> login
>> 1011
>> cvs -z3 -d:pserver:[EMAIL PROTECTED]:/cvsroot/lirc
>> co -P lirc
>> 1012 cd lirc/
>> 1019 ./autogen.sh
>> 1025 ./setup.sh
>> 1026 make
>> 1027 make install
>> 1028 depmod
>>
>>
>> modprobe lirc_dev debug=1
>> modprobe lirc_i2c debug=1
>> lircd
>>
>> lirc_dev: IR Remote Control driver registered, at major 61
>> lirc_i2c: probe 0x1a @ ivtv i2c driver #0: no
>> lirc_i2c: probe 0x18 @ ivtv i2c driver #0: no
>> lirc_i2c: probe 0x71 @ ivtv i2c driver #0: no
>> lirc_i2c: probe 0x4b @ ivtv i2c driver #0: no
>> lirc_i2c: probe 0x64 @ ivtv i2c driver #0: no
>> lirc_i2c: probe 0x30 @ ivtv i2c driver #0: no
>> lirc_i2c: probe 0x6b @ ivtv i2c driver #0: no
>>
>> [EMAIL PROTECTED] lirc]# tail /var/log/lircd
>> Jun 27 19:05:19 media.nzbaxters lircd: accepted new client on /dev/lircd
>> Jun 27 19:05:19 media.nzbaxters lircd: could not open /dev/lirc
>> Jun 27 19:05:19 media.nzbaxters lircd: default_init(): No such device
>> Jun 27 19:05:19 media.nzbaxters lircd: caught signal
>> Jun 27 19:12:29 media.nzbaxters lircd: lircd(hauppauge) ready
>>
>>
>> Am I not including something when I compile or something?
>>
>> I did see this message:
>> "You should add the contents of `/usr/share/aclocal/libtool.m4' to
>> `aclocal.m4'."
>>
>>
>> ivtv seems ok:
>> Linux video capture interface: v1.00
>> ivtv: ==================== START INIT IVTV ====================
>> ivtv: version 0.6.3 (development snapshot compiled on Sat 17 Jun 2006
>> 03:30:00 PM PDT) loading
>> ivtv: Linux version: 2.6.16.18 686 REGPARM 4KSTACKS gcc-4.1
>> ivtv: In case of problems please include the debug info between
>> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
>> ivtv: any module options, when mailing the ivtv-users mailinglist.
>> ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
>> ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 21
>> ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
>> tveeprom 1-0050: Hauppauge model 26132, rev F0B2, serial# 9400151
>> tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 4)
>> tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
>> tveeprom 1-0050: audio processor is CX25841 (idx 35)
>> tveeprom 1-0050: decoder processor is CX25841 (idx 28)
>> tveeprom 1-0050: has no radio, has IR remote
>> tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
>> cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
>> cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
>> wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
>> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
>> ivtv0: Encoder revision: 0x02050032
>> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
>> total)
>> ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB
>> total)
>> ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB
>> total)
>> ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
>> total)
>> tuner 1-0061: type set to 50 (TCL 2002N)
>> ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
>> ivtv: ==================== END INIT IVTV ====================
>>
>>
>>
>> What am I missing here????
>>
>>
>>
>> _______________________________________________
>> ivtv-devel mailing list
>> [email protected]
>> http://ivtvdriver.org/mailman/listinfo/ivtv-devel
>>
>
>
--------------------------------------------------------------------------------
> _______________________________________________
> ivtv-devel mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-devel
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
