> $ diff lirc/drivers/lirc_i2c/lirc_i2c.c lirc\
> 062106/drivers/lirc_i2c/lirc_i2c.c
> < /* $Id: lirc_i2c.c,v 1.38 2006/06/26 23:21:34 lirc Exp $ */
>> /* $Id: lirc_i2c.c,v 1.37 2006/05/20 04:38:58 lirc Exp $ */
> < #ifdef I2C_HW_B_CX2341X
> < if (adap->id == (I2C_ALGO_BIT | I2C_HW_B_BT848) ||
> < adap->id == (I2C_ALGO_BIT | I2C_HW_B_CX2341X))
> < #else
> < if (adap->id == (I2C_ALGO_BIT | I2C_HW_B_BT848))
> < #endif
> < {
> ---
>> if (adap->id == (I2C_ALGO_BIT | I2C_HW_B_BT848)) {
>
> Seems to have added some checking for i2c definitions for I2C_HW_B_CX2341X
> (kernel 2.6.17+) and I2C_HW_B_BT848. Certainly looks like some updates in
> the right areas, but proof will be in the pudding!
>
> Will try it tonight....
There must be something fundamental I'm doing wrong. I get the same
problem:
1010 cvs -d:pserver:[EMAIL PROTECTED]:/cvsroot/lirc
login
1011 cvs -z3 -d:pserver:[EMAIL PROTECTED]:/cvsroot/lirc
co -P lirc
1012 cd lirc/
1019 ./autogen.sh
1025 ./setup.sh
1026 make
1027 make install
1028 depmod
modprobe lirc_dev debug=1
modprobe lirc_i2c debug=1
lircd
lirc_dev: IR Remote Control driver registered, at major 61
lirc_i2c: probe 0x1a @ ivtv i2c driver #0: no
lirc_i2c: probe 0x18 @ ivtv i2c driver #0: no
lirc_i2c: probe 0x71 @ ivtv i2c driver #0: no
lirc_i2c: probe 0x4b @ ivtv i2c driver #0: no
lirc_i2c: probe 0x64 @ ivtv i2c driver #0: no
lirc_i2c: probe 0x30 @ ivtv i2c driver #0: no
lirc_i2c: probe 0x6b @ ivtv i2c driver #0: no
[EMAIL PROTECTED] lirc]# tail /var/log/lircd
Jun 27 19:05:19 media.nzbaxters lircd: accepted new client on /dev/lircd
Jun 27 19:05:19 media.nzbaxters lircd: could not open /dev/lirc
Jun 27 19:05:19 media.nzbaxters lircd: default_init(): No such device
Jun 27 19:05:19 media.nzbaxters lircd: caught signal
Jun 27 19:12:29 media.nzbaxters lircd: lircd(hauppauge) ready
Am I not including something when I compile or something?
I did see this message:
"You should add the contents of `/usr/share/aclocal/libtool.m4' to
`aclocal.m4'."
ivtv seems ok:
Linux video capture interface: v1.00
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.6.3 (development snapshot compiled on Sat 17 Jun 2006
03:30:00 PM PDT) loading
ivtv: Linux version: 2.6.16.18 686 REGPARM 4KSTACKS gcc-4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 21
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom 1-0050: Hauppauge model 26132, rev F0B2, serial# 9400151
tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 4)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: audio processor is CX25841 (idx 35)
tveeprom 1-0050: decoder processor is CX25841 (idx 28)
tveeprom 1-0050: has no radio, has IR remote
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
tuner 1-0061: type set to 50 (TCL 2002N)
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv: ==================== END INIT IVTV ====================
What am I missing here????
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
