> You need the 0.10 branch. Get it here: > > http://ivtvdriver.org/viewcvs/ivtv/branches/0.10.tar.gz?view=tar > > Hans
Hi Hans, Thanks one more time, but it did not help. After cold reboot, IR disappeared again. I tried with and without newi2c=1. And --reset-ir gives me the same error as you can see below. [EMAIL PROTECTED]:/home/mm# modprobe lirc_i2c debug=1 [EMAIL PROTECTED]:/home/mm# dmesg | grep lirc_ lirc_dev: IR Remote Control driver registered, at major 61 lirc_i2c: probe 0x1a @ ivtv i2c driver #0: no lirc_i2c: probe 0x18 @ ivtv i2c driver #0: no lirc_i2c: probe 0x71 @ ivtv i2c driver #0: no lirc_i2c: probe 0x4b @ ivtv i2c driver #0: no lirc_i2c: probe 0x64 @ ivtv i2c driver #0: no lirc_i2c: probe 0x30 @ ivtv i2c driver #0: no lirc_i2c: probe 0x6b @ ivtv i2c driver #0: no [EMAIL PROTECTED]:/home/mm# ivtvctl --reset-ir ioctl VIDIOC_INT_RESET failed: Invalid argument [EMAIL PROTECTED]:/home/mm# ivtvctl --version ivtvctl version 0.10.2 (development snapshot compiled on Fr 13 Apr 2007 12:12:44 CEST) ivtv in dmesg: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.10.2 (development snapshot compiled on Fr 13 Apr 2007 12:12:48 CEST) loading ivtv: Linux version: 2.6.20.1 SMP mod_unload K8 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge card (cx23416 based) ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 ACPI: PCI Interrupt 0000:03:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 21 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv0: Encoder revision: 0x02060039 tveeprom 2-0050: Hauppauge model 26134, rev F1B3, serial# 10233063 tveeprom 2-0050: tuner model is TCL M2523_3DB_E (idx 113, type 55) tveeprom 2-0050: TV standards PAL(B/G) PAL(D/D1/K) (eeprom 0x44) tveeprom 2-0050: audio processor is CX25842 (idx 36) tveeprom 2-0050: decoder processor is CX25842 (idx 29) tveeprom 2-0050: has no radio, has IR receiver, has IR transmitter ivtv0: Autodetected Hauppauge WinTV PVR-150 ivtv0: reopen i2c bus for IR-blaster support tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 2-0044: cx25842-23 found @ 0x88 (ivtv i2c driver #0) cx25840 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: Registered device video0 for encoder MPEG (4 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video24 for encoder PCM audio (1 MB) tuner 2-0061: type set to 55 (TCL 2002MB) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== _______________________________________________ ivtv-devel mailing list [EMAIL PROTECTED] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
