Thanks Hans,
I really appreciate you helping me!
> It should load the cx25840 driver automatically. If not, then I suspect
> broken hardware. If it IS loaded, then something else might be wrong.
> However, I can't access you older emails at the moment to look at the
> dmesg output.
>
> Hans
Can't find any indication that the cx25840 driver is loaded.
Here's the dmesg output again.
Linux video capture interface: v1.00
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.3 (tagged release) loading
ivtv: Linux version: 2.6.15-1.1833_FC4 686 REGPARM 4KSTACKS gcc-4.0
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKC] -> GSI 9 (level,
low) ->
IRQ 9
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom: The eeprom says no radio is present, but the tuner type 60
tveeprom: indicates otherwise. I will assume that radio is present.
tveeprom: ivtv version
tveeprom: Hauppauge: model = 26559, rev = C260, serial# = 2993543
tveeprom: tuner = LG S001D MK3 (idx = 60, type = 38)
tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom =
0x74,
v4l2 = 0x00400e17)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c!
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
tda9887 0-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB
total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB
total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
ivtv0: Create encoder radio stream
tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv
i2c
driver #0
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40085618!
ivtv0 warning: i2c client addr: 0x44 not found for command 0xc0045627!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40046d11!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40085618!
ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40045613!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x402c5639!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40045612!
ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c!
ivtv0: Initialized WinTV PVR 150, card #0
ivtv: ==================== END INIT IVTV ====================
> -----Oorspronkelijk bericht-----
> Van: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] Hans Verkuil
> Verzonden: donderdag 16 maart 2006 15:13
> Aan: User discussion about IVTV
> Onderwerp: Re: [ivtv-users] ivtv0 warning: i2c
>
>
> > Hi Hans,
> >
> > Thanks for the reply.
> > So I guess its the decoder processor? The card previously ran
> on a XP MCE.
> > No problems there.
> > You say its the cx25840 chip it cannot find. However, this card uses a
> > cx25843 chip.
>
> Same thing.
>
> > > tveeprom: decoder processor = CX25843 (type = 1e)
> > Does this mean I need other drivers? If so can you point me in the right
> > direction?
>
> It should load the cx25840 driver automatically. If not, then I suspect
> broken hardware. If it IS loaded, then something else might be wrong.
> However, I can't access you older emails at the moment to look at the
> dmesg output.
>
> Hans
>
>
> >
> > Best regards,
> > Hansa
> >
> > -----Oorspronkelijk bericht-----
> > Van: [EMAIL PROTECTED]
> > [mailto:[EMAIL PROTECTED] Hans Verkuil
> > Verzonden: donderdag 16 maart 2006 14:42
> > Aan: User discussion about IVTV
> > Onderwerp: Re: [ivtv-users] ivtv0 warning: i2c
> >
> >
> >> Hi,
> >> I can't record at all. I can't even see live TV.
> >> Seems like nobody knows why I get the warnings:
> >> ivtv0 warning: i2c client addr: 0x44 not found for command
> 0x40085618!
> >
> > That's the cx25840 chip that it cannot find. Better check your card in a
> > Windows system. My guess is that your card is broken.
> >
> > Hans
> >
> >>
> >> (see my previous mail regarding "[ivtv-users] ivtv0 warning: i2c" for a
> >> complete output)
> >>
> >> Regards,
> >> Hansa
> >>
> >> -----Oorspronkelijk bericht-----
> >> Van: [EMAIL PROTECTED]
> >> [mailto:[EMAIL PROTECTED] Zsombor BOLYOCZKI
> >> Verzonden: donderdag 16 maart 2006 12:45
> >> Aan: User discussion about IVTV
> >> Onderwerp: Re: [ivtv-users] ivtv0 warning: i2c
> >>
> >>
> >> Hi,
> >>
> >>
> >> I have similar problem: I can't record tv with my PVR 150 card using
> >> cron
> >> because I got similar warnings.
> >>
> >> Can you do scheduled recording or this is my private problem? B-/
> >>
> >> zsombor
> >>
> >>
> >>> By the way,
> >>>
> >>> Why is there only MPEG decoder firmware available for
> wintv-pvr 250-350
> >>> and
> >>> not for pvr150?
> >>> Are they the same for both cards or am I just blind?
> >>
> >>
> >>
_____________________________________________
> ivtv-users mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-users
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
