On Jun 29, 2006, at 1:27 PM, Kenneth Hester wrote: > I can't seem to get my PVR 500 MCE to work. I have tried several > distributions > and ivtv versions. Has anyone had any success with this? > > The driver also reports that it doesn't recognize the second unit > on the > card. > Is this normal? Right after that it says it is the 2nd unit on a 500. > > It was purchased from Dell. > It is a PVR 500 MCE with and FM receiver and no remote on the card. > > The first tuner works slightly. It has complete snow on the lower > channels > and slight snow on the upper channels. I am in the US on cable and > the > frequencies appear to be correct (2=55.250, 75=529.250). The sound is > always good on all channels. I am running SUSE 10.1 with > ivtv-0.6.3 with > suse built kernel 2.6.16.13-default > I have also tried 0.6.2 on SUSE 10.1 and 0.4.2 on SUSE 10.0 and the > KnoppMyth distribution with the same results. The card appears to > work properly under Windoze. > > The second tuner does not work. > In modprobe.conf I have these lines: > alias char-major-81-0 off > alias char-major-81-1 ivtv > alias char-major-81-2 ivtv
What's up with the "off" line? I'm not sure that will work. If you're trying to force the PVR-500 onto video1 and video2, do this : alias char-major-81 ivtv alias char-major-81-1 ivtv alias char-major-81-2 ivtv options ivtv ivtv_first_minor=1 If you look through the dmesg output, you'll see that the first card detected is the second unit of the PVR-500, not the first. Keith C > > lspci -v shows the cards as below. I included the sound card > because it > seems to share the same IRQ > as the second tuner: > 00:1f.5 Multimedia audio controller: Intel Corporation 82801AA > AC'97 Audio > (rev 02) > Subsystem: Unknown device 4352:5933 > Flags: bus master, medium devsel, latency 0, IRQ 10 > I/O ports at 1200 [size=256] > I/O ports at 1300 [size=64] > > 02:08.0 Multimedia video controller: Internext Compression Inc iTVC16 > (CX23416) MPEG-2 Encoder (rev 01) > Subsystem: Hauppauge computer works Inc. WinTV PVR 500 (1st unit) > Flags: bus master, medium devsel, latency 64, IRQ 11 > Memory at f4000000 (32-bit, prefetchable) [size=64M] > Capabilities: [44] Power Management version 2 > > 02:09.0 Multimedia video controller: Internext Compression Inc iTVC16 > (CX23416) MPEG-2 Encoder (rev 01) > Subsystem: Hauppauge computer works Inc. WinTV PVR 500 (2nd unit) > Flags: bus master, medium devsel, latency 64, IRQ 10 > Memory at f8000000 (32-bit, prefetchable) [size=64M] > Capabilities: [44] Power Management version 2 > > I am running the current firmware: > 305dba74bbe5905447add8883f3ecb68 v4l-cx2341x-dec.fw > 5f5fa240ada73c3565f5f7de4c7b5138 v4l-cx2341x-enc.fw > 99836e41ccb28c7b373e87686f93712a v4l-cx25840.fw > > The v4l-cx2341x-enc.fw also matches the CD shipped by Hauppauge > with the > card. > > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.6.3 (tagged release) loading > ivtv: Linux version: 2.6.16.13-4-default 586 REGPARM gcc-4.1 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) > tveeprom 0-0050: Hauppauge model 23552, rev D487, serial# 9525425 > tveeprom 0-0050: tuner model is Samsung TCPN 2121P30A (idx 87, type > 70) > tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) > tveeprom 0-0050: second tuner model is Philips TEA5768HL FM Radio > (idx 101, > type 62) > tveeprom 0-0050: audio processor is CX25843 (idx 37) > tveeprom 0-0050: decoder processor is CX25843 (idx 30) > tveeprom 0-0050: has radio, has no IR remote > ivtv0: This is the second unit of a PVR500 > ivtv0: Correcting tveeprom data: no radio present on second unit > usbcore: registered new driver usbfs > usbcore: registered new driver hub > USB Universal Host Controller Interface driver v2.3 > PCI: Found IRQ 9 for device 0000:00:1f.2 > PCI: Setting latency timer of device 0000:00:1f.2 to 64 > uhci_hcd 0000:00:1f.2: UHCI Host Controller > uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1 > uhci_hcd 0000:00:1f.2: irq 9, io base 0x00001820 > usb usb1: new device found, idVendor=0000, idProduct=0000 > usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb1: Product: UHCI Host Controller > usb usb1: Manufacturer: Linux 2.6.16.13-4-default uhci_hcd > usb usb1: SerialNumber: 0000:00:1f.2 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 2 ports detected > tuner 0-0060: TEA5767 detected. > tuner 0-0060: chip found @ 0xc0 (ivtv i2c driver #0) > tuner 0-0060: type set to 62 (Philips TEA5767HN FM Radio) > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) > i810_smbus 0000:00:01.0: i810/i815 i2c device found. > i2c-algo-bit.o: (0) scl=1, sda=1 > i2c-algo-bit.o: (1) scl=1, sda=0 > i2c-algo-bit.o: (2) scl=1, sda=1 > i2c-algo-bit.o: (3) scl=0, sda=1 > i2c-algo-bit.o: (4) scl=1, sda=1 > i2c-algo-bit.o: I810/I815 I2C Adapter passed test. > usb 1-1: new full speed USB device using uhci_hcd and address 2 > Linux agpgart interface v0.101 (c) Dave Jones > usb 1-1: new device found, idVendor=0609, idProduct=031d > usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3 > usb 1-1: Product: eHome Infrared Transceiver > usb 1-1: Manufacturer: SMK > usb 1-1: SerialNumber: SM0059g4 > usb 1-1: configuration #1 chosen from 1 choice > i8xx TCO timer: initialized (0x1060). heartbeat=30 sec (nowayout=0) > hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33) > Uniform CD-ROM driver Revision: 3.20 > JBD: barrier-based sync failed on hda3 - disabling barriers > cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes) > i2c-algo-bit.o: (0) scl=1, sda=1 > i2c-algo-bit.o: (1) scl=1, sda=0 > i2c-algo-bit.o: (2) scl=1, sda=1 > i2c-algo-bit.o: (3) scl=0, sda=1 > i2c-algo-bit.o: (4) scl=1, sda=1 > i2c-algo-bit.o: I810/I815 DDC Adapter passed test. > agpgart: Detected an Intel i810 Chipset. > agpgart: AGP aperture is 64M @ 0xf0000000 > wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > ivtv0: Encoder revision: 0x02050032 > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers > (4096KB total) > ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB > total) > ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB > total) > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers > (2048KB > total) > tuner 0-0061: type set to 70 (Samsung TCPN 2121P30A) > ivtv0: Initialized WinTV PVR 500 (unit #2), card #0 > ivtv: ====================== NEXT CARD ====================== > ivtv1: Unknown card: vendor/device: 4444/0016 > ivtv1: subsystem vendor/device: 0070/b7f7 > ivtv1: cx23416 based > ivtv1: Defaulting to Hauppauge WinTV PVR-150 card > ivtv1: Please mail the vendor/device and subsystem vendor/device > IDs and > what kind of > ivtv1: card you have to the ivtv-devel mailinglist > (www.ivtvdriver.org) > ivtv1: Prefix your subject line with [UNKNOWN CARD]. > tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #1) > cx25840 3-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1) > cx25840 3-0044: loaded v4l-cx25840.fw firmware (16382 bytes) > wm8775 3-001b: chip found @ 0x36 (ivtv i2c driver #1) > tveeprom 3-0050: Hauppauge model 23552, rev D487, serial# 9525425 > tveeprom 3-0050: tuner model is Samsung TCPN 2121P30A (idx 87, type > 70) > tveeprom 3-0050: TV standards NTSC(M) (eeprom 0x08) > tveeprom 3-0050: second tuner model is Philips TEA5768HL FM Radio > (idx 101, > type 62) > tveeprom 3-0050: audio processor is CX25843 (idx 37) > tveeprom 3-0050: decoder processor is CX25843 (idx 30) > tveeprom 3-0050: has radio, has no IR remote > ivtv1: This is the second unit of a PVR500 > ivtv1: Correcting tveeprom data: no radio present on second unit > ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > ivtv1 warning: Encoder mailbox not found > ivtv1 warning: Decoder mailbox not found > ivtv1: Error locating firmware. > ivtv1: Error -12 on initialization > ivtv: probe of 0000:02:09.0 failed with error -12 > ivtv: ==================== END INIT IVTV ==================== > > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
