I appear to have the same issue with pvr 250s and IVTV 0.4.6 Driver.
Video comes in fine but no audio.
sample #cat /dev/video0 >
http://metavidcap.ucsc.edu/raw_mpeg2/ivtv0.4.6_no_audio.mpg
dmesg | tac |
sed -n '/=\ \ END INIT IVTV\ \ =/,/= START INIT IVTV =/p;
/= START INIT IVTV =/q' |
tac
ivtv: version 0.4.6 (tagged release) loading
ivtv: Linux version: 2.6.15-1.1833_FC4 gcc-4.0
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected WinTV PVR 250 card (cx23416 based)
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 201
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom: ivtv version
tveeprom: Hauppauge: model = 32552, rev = C168, serial# = 7758111
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = MSP4448 (type = 1b)
tveeprom: decoder processor = SAA7115 (type = 13)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
ivtv0: Failed to load module msp3400
tda9887 1-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
ivtv0: Create encoder radio stream
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
ivtv0 warning: i2c client addr: 0x40 not found for command 0x40086d11!
ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610!
ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611!
ivtv0 warning: i2c client addr: 0x40 not found for command 0x40085618!
ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610!
ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611!
ivtv0 warning: i2c client addr: 0x40 not found for command 0x402c5639!
ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610!
ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611!
ivtv0: Initialized WinTV PVR 250, card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 250 card (cx23416 based)
GSI 21 sharing vector 0xD1 and IRQ 21
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 209
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom: ivtv version
tveeprom: Hauppauge: model = 32552, rev = C168, serial# = 7881541
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = MSP4448 (type = 1b)
tveeprom: decoder processor = SAA7115 (type = 13)
ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=saa7115, addr=21]
tda9887 2-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]
ivtv1: Failed to load module msp3400
ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv1: Encoder revision: 0x02050032
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
ivtv1: Create encoder radio stream
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #1
ivtv1 warning: i2c client addr: 0x40 not found for command 0x40086d11!
ivtv1 warning: i2c client addr: 0x40 not found for command 0x80287610!
ivtv1 warning: i2c client addr: 0x40 not found for command 0x40287611!
ivtv1 warning: i2c client addr: 0x40 not found for command 0x40085618!
ivtv1 warning: i2c client addr: 0x40 not found for command 0x80287610!
ivtv1 warning: i2c client addr: 0x40 not found for command 0x40287611!
ivtv1 warning: i2c client addr: 0x40 not found for command 0x402c5639!
ivtv1 warning: i2c client addr: 0x40 not found for command 0x80287610!
ivtv1 warning: i2c client addr: 0x40 not found for command 0x40287611!
ivtv1: Initialized WinTV PVR 250, card #1
ivtv: ==================== END INIT IVTV ====================
lspci -v
00:06.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device 4801
Flags: bus master, medium devsel, latency 64, IRQ 201
Memory at c8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
00:08.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device 4801
Flags: bus master, medium devsel, latency 64, IRQ 209
Memory at c4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host
Bridge (rev 01)
Subsystem: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge
Flags: bus master, 66Mhz, medium devsel, latency 8
Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [80] AGP version 3.0
Capabilities: [c0] HyperTransport: Slave or Primary Interface
Capabilities: [68] Power Management version 2
Capabilities: [58] HyperTransport: Interrupt Discovery and
Configuration
--michael
G. Jagadish wrote:
>
> Hi,
>
> I'm using FC3 with 2.6.12-1_1381 Kernel and PVR 150 card with IVTV
> 0.4.6 Driver.
>
> I'm getting only video and no audio. pls help me in this,
>
> modprobe.conf
> ------------------------
> alias eth0 8139too
> alias scsi_hostadapter ata_piix
> alias snd-card-0 snd-intel8x0
> options snd-card-0 index=0
> install snd-intel8x0 /sbin/modprobe --ignore-install snd-intel8x0 &&
> /usr/sbin/alsactl restore >/dev/null 2>&1 || :
> remove snd-intel8x0 { /usr/sbin/alsactl store >/dev/null 2>&1 || : ;
> }; /sbin/modprobe -r --ignore-remove snd-intel8x0
> alias usb-controller ehci-hcd
> alias usb-controller1 uhci-hcd
> alias char-major-81 ivtv
> --------------------------
>
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.4.6 (tagged release) loading
> ivtv: Linux version: 2.6.12-1.1381_FC3 686 REGPARM 4KSTACKS gcc-3.4
> ivtv: In case of problems please include the debug info between
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> ivtv: any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Autodetected WinTV PVR 250 card (cx23416 based)
> ACPI: PCI Interrupt 0000:01:04.0[A] -> Link [LNKC] -> GSI 10 (level,
> low) -> IRQ 10
> ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
> ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> tveeprom: Hauppauge: model = 26139, rev = G1A5, serial# = 9533907
> tveeprom: tuner = <unknown> (idx = 105, type = -1069826176)
> tveeprom: tuner fmt = PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17)
> tveeprom: audio_processor = MSP3400C (type = 4)
> ivtv0: Corrected autodetection from WinTV PVR 250 to WinTV PVR 150
> ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
> tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> cx25840 1-0044: ivtv driver
> cx25840 1-0044: cx25842-23 found @ 0x88 (ivtv i2c driver #0)
> cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
> ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
> wm8775 1-001b: ivtv driver
> wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
> tda9885/6/7: chip found @ 0x86
> ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
> total)
> ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
> ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
> ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers
> (2048KB total)
> ivtv0: Create encoder radio stream
> tuner 1-0061: tuner type not set
> ivtv0: Initialized WinTV PVR 150, card #0
> ivtv: ==================== END INIT IVTV ====================
>
> ------------------------------------------------------
>
> Thanx in Advance
> Jagadish
> ------------------------------------------------------------------------
>
> _______________________________________________
> ivtv-users mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-users
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
