Hi Vineet, The Junos version is 9.0R1.10, the firmware of the PIC is 2.2
J-TAC are also asking the same questions now :) Thanks, Lee -----Original Message----- From: Vineet Venugopal [mailto:[EMAIL PROTECTED] Sent: 17 June 2008 16:43 To: Lee Hetherington Cc: [EMAIL PROTECTED]; juniper-nsp@puck.nether.net Subject: Re: [j-nsp] Serial Question Hi Lee, Can you confirm the JUNOS version running on the Router as well as the firmware version of the interface "show system firmware"? Regards Vineet On 6/17/08, Lee Hetherington <[EMAIL PROTECTED]> wrote: > Hi Alain, > > Im also not sure why I configured the clocking type :) > > I will connect it all up later on and drop you the output. > > Thanks for this > > Lee > > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > Sent: 17 June 2008 16:13 > To: Lee Hetherington; juniper-nsp@puck.nether.net > Subject: RE: [j-nsp] Serial Question > > Hi Lee > > Can you provide us for some traces: > > Monitor trafic interface se-1/0/1 > We will see the lmi traffic > And > Show interface se-1/0/1 extensive > > I believe it's an LMI problem > Normaly the default lmi on Juniper is ansi like the one you've configured on > Cisco (so this should be OK) > But perhaps the keepalive could be adapted (5 ?) > I am also wondering why you configured "serial-option: clocking-mode loop" ! > > > Alain > > > > > -----Message d'origine----- > De : [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] De la part de Lee > Hetherington > Envoyé : mardi 17 juin 2008 14:06 > À : juniper-nsp@puck.nether.net > Objet : [j-nsp] Serial Question > > Hi All, > > I have a J2320-JH which is replacing an aging Cisco 3640. I am having > trouble bringing up an x.21 leased line. It brings up the line, but in cisco > terms not the protocol. It keeps telling me on my subinterface > "flags: down". > > Below are my cisco and juniper configs. Anyone any ideas, the isp is being > particularly un-helpful. > > Cisco: > > ! > interface Serial0/0 > bandwidth 2048 > no ip address > encapsulation frame-relay > no ip mroute-cache > keepalive 5 > no fair-queue > frame-relay lmi-type ansi > ! > interface Serial0/0.16 point-to-point > description Telstra Circuit > ip address 154.32.xxx.81 255.255.255.252 no cdp enable frame-relay > interface-dlci 16 IETF ! > > > Juniper: > > se-1/0/1 { > description Telstra; > mtu 1500; > encapsulation frame-relay; > serial-options { > clocking-mode loop; > } > unit 0 { > description "Telstra Serial Circuit MXFS203988"; > point-to-point; > dlci 16; > family inet { > address 154.32.152.81/30; > } > } > } > > Many Thanks, > > Lee > > _______________________________________________ > juniper-nsp mailing list juniper-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/juniper-nsp > > -- > This message has been scanned for viruses and > dangerous content by REDScanner, and is > believed to be clean. > > _______________________________________________ > juniper-nsp mailing list juniper-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/juniper-nsp > -- ---Vineet -- This message has been scanned for viruses and dangerous content by REDScanner, and is believed to be clean. _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp