:) FPC 0 E-FPC PIC 2 REV 14 750-014895 DH5587 MultiServices 100 PIC 3 REV 17 750-007626 CZ1730 10x CHE1 IQ
There is no predefined and configureable lsq interface seen at M10i when you run "show interfaces" though.. As i understand from your explanation that the lsq-0/2/0 interface should already exists as we already have MSPIC at FPC 0 but; ilker# set interfaces lsq-0/2/0 unit 0 family inet address 1.2.3.4/32 [edit] ilker# commit check [edit] 'interfaces' sp-0/2/0 and lsq-0/2/0 cannot be configured on the same physical interface error: configuration check-out failed That's why i was asking for it to be sure.. Any clues about it? -----Original Message----- From: Stefan Fouant [mailto:[EMAIL PROTECTED] Sent: Thursday, June 26, 2008 5:55 PM To: Ilker YILMAZ Cc: [EMAIL PROTECTED]; juniper-nsp@puck.nether.net Subject: Re: [j-nsp] Load-Balance on Internet Processor II Dude... it's lsq-x/x/x... x/x/x corresponds to whatever FPC/PIC combination you've got your AS or MS PIC installed. The slot should always be 0 on these interfaces. So if you've got an MS-PIC installed in FPC 2, PIC 1... the interface should be lsq-2/1/0. Do a 'show chassis hardware' to identify where your PIC is installed. -- Stefan Fouant Principal Network Engineer NeuStar, Inc. - http://www.neustar.biz GPG Key ID: 0xB5E3803D On Thu, Jun 26, 2008 at 10:39 AM, Ilker YILMAZ <[EMAIL PROTECTED]> wrote: > > Thanks Steinar & Erdem for your help, i see ls-0/0/0 interface at > J4350 whereas i have no clue about at M10i interface naming for MLPPP. > > Does anybody have information on that? > > Thanks! > Ilker > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > Sent: Thursday, June 26, 2008 12:35 PM > To: [EMAIL PROTECTED] > Cc: juniper-nsp@puck.nether.net > Subject: Re: [j-nsp] Load-Balance on Internet Processor II > >> Do you know which interface naming is available at J4350 & M10i for >> MLPPP > ? >> I see ls-0/0/0 interface at J4350 and lsi.x at M10i (Includes MSPIC) > > Interface naming depends on what PICs you have. Here's an example from > an M7i with ASM, channelized STM-1 and 4 E1s in a bundle using the ASM: > > e1-0/2/0:1 up up > e1-0/2/0:1.0 up up mlppp lsq-1/2/0.1 > e1-0/2/0:2 up up > e1-0/2/0:2.0 up up mlppp lsq-1/2/0.1 > e1-0/2/0:3 up up > e1-0/2/0:3.0 up up mlppp lsq-1/2/0.1 > e1-0/2/0:4 up up > e1-0/2/0:4.0 up up mlppp lsq-1/2/0.1 > lsq-1/2/0 up up > lsq-1/2/0.1 up up inet 192.168.10.5/30 > > Steinar Haug, Nethelp consulting, [EMAIL PROTECTED] > > > > _______________________________________________ > juniper-nsp mailing list juniper-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/juniper-nsp > -- Stefan Fouant Principal Network Engineer NeuStar, Inc. - http://www.neustar.biz GPG Key ID: 0xB5E3803D _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp