Hi Antonio, yes, interface ge-0/0/0 is only configure for ospf3 and interface fe-0/1/0 is configued for dual-stack.
Here, I have listed the required configuation as you have asked. scenario Cisco-rtr ------------------ ge-0/0/0 (M10i) fe-0/1/0 ----------------- Cisco-rtr ospf3 dual-stack ospf2 and ospf3 M10i config show configuration protocols ospf preference 110; area 0.0.0.10 { interface lo0.0 { passive; } interface fe-0/1/0.0; interface fxp0.0 { disable; } interface fe-0/1/1.0 { passive; } interface fe-0/1/2.0 { passive; } interface fe-0/3/0.0 { passive; } } show configuration protocols ospf3 preference 110; area 0.0.0.10 { interface ge-0/0/0.0; interface lo0.0 { passive; } interface fe-0/3/1.0 { passive; } interface fe-0/1/0.0; show ospf interface Interface State Area DR ID BDR ID Nbrs fe-0/1/0.0 BDR 0.0.0.10 x.x.192.4 x.x.192.1 1 fe-0/1/1.0 DRother 0.0.0.10 0.0.0.0 0.0.0.0 0 fe-0/1/2.0 DRother 0.0.0.10 0.0.0.0 0.0.0.0 0 fe-0/3/0.0 DRother 0.0.0.10 0.0.0.0 0.0.0.0 0 lo0.0 DRother 0.0.0.10 0.0.0.0 0.0.0.0 0 show ospf3 interface OSPF instance is not running The neighbor cisco devices, one connected to m10i fe-0/1/0 and another cisco device connected to M10i ge-0/0/0 cisco config output connected to M10i fe-0/1/0 #sh run | be ^ipv6 router ospf ipv6 router ospf 1 router-id x.x.192.4 log-adjacency-changes passive-interface default no passive-interface FastEthernet0/0 #sh run int fa0/0 Building configuration... Current configuration : 284 bytes ! interface FastEthernet0/0 description *** *** ip address x.x.193.4 255.255.255.240 no keepalive duplex full ipv6 address abcd:3800:2:1::2/126 ipv6 enable ipv6 ospf 1 area 10 no cdp enable no clns route-cache end #sh ipv6 ospf int FastEthernet0/0 is up, line protocol is up Link Local Address FE80::20C:31FF:FE95:A400, Interface ID 3 Area 10, Process ID 1, Instance ID 0, Router ID x.x.192.4 Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) x.x.192.4, local address FE80::20C:31FF:FE95:A400 No backup designated router on this network Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:00 Index 1/1/2, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 0, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) Loopback6 is up, line protocol is up Link Local Address FE80::20C:31FF:FE95:A400, Interface ID 15 Area 10, Process ID 1, Instance ID 0, Router ID x.x.192.4 Network Type LOOPBACK, Cost: 1 Loopback interface is treated as a stub Host cisco config output connected to M10i ge-0/0/0 #sh run int fa0/0 Building configuration... Current configuration : 258 bytes ! interface FastEthernet0/0 description *** *** ip address x.x.193.72 255.255.255.192 ip route-cache flow duplex auto speed auto ipv6 address abcd:3800:1:1::2/64 ipv6 enable ipv6 ospf 1 area 10 no cdp enable end #sh run | be ^ipv6 router ospf ipv6 router ospf 1 router-id x.x.192.2 log-adjacency-changes passive-interface default no passive-interface FastEthernet0/0 #sh ipv6 int fa0/0 FastEthernet0/0 is up, line protocol is up IPv6 is enabled, link-local address is FE80::218:73FF:FE46:1232 Description: *** *** Global unicast address(es): abcd:3800:1:1::2, subnet is abcd:3800:1:1::/64 Joined group address(es): FF02::1 FF02::2 FF02::5 FF02::6 FF02::1:FF00:2 FF02::1:FF46:1232 MTU is 1500 bytes ICMP error messages limited to one every 100 milliseconds ICMP redirects are enabled ND DAD is enabled, number of DAD attempts: 1 ND reachable time is 30000 milliseconds ND advertised reachable time is 0 milliseconds ND advertised retransmit interval is 0 milliseconds ND router advertisements are sent every 200 seconds ND router advertisements live for 1800 seconds Hosts use stateless autoconfig for addresses. Have a query that is, why even the static route didn't worked on the box? Thank you, Ramesh On Sun, Apr 4, 2010 at 6:56 PM, Antonio Querubin <t...@lava.net> wrote: > On Sun, 4 Apr 2010, Ramesh Karki wrote: > > As I have already mentioned, the same interface fe-0/1/0 has been >> configured >> to run both ospf and ospf3 and there is no any issue on ospf v4 from the >> beginning. >> >> show ospf interface fe-0/1/0.0 >>> >> Interface State Area DR ID BDR ID >> Nbrs >> fe-0/1/0.0 BDR 0.0.0.10 x.x.192.4 x.x.192.1 >> 1 >> >> but the same interface configured for ospf3 outcome is unexpected. >> >> show ospf3 interface fe-0/1/0.0 >>> >> OSPF instance is not running >> > > Reviewing what you've posted so far I only see a partial ospf3 config for > ge-0/0/0.0 > > Could you please post the complete output of: > > show configuration protocols ospf > show configuration protocols ospf3 > show ospf interface > show ospf3 interface > > Then for your dual-stack interfaces which should be running ospf and ospf3 > do: > > show configuration interfaces > > On your ciscos which have a working ospf3 config do > > show running-config | begin ipv6 router ospf > show ipv6 ospf interface > > show running-config interface <each dual-stack interface that faces a > juniper> > > > Antonio Querubin > 808-545-5282 x3003 > e-mail/xmpp: t...@lava.net > _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp