Is Junos 12.3 more strict about 3rd party MSA optics than 11.4? I've been using 3rd party MSA optics in EX without troubles, including DOM support working fine. I just deployed a new EX4200 VC with 12.3R6, and the DOM isn't working on the 3rd party MSA optics (but the link comes up and works), but those same optics work with DOM on an MX running 11.4. Interesting that it says "unknown cable" whereas my other 3rd party CWDM SFP+ optics say "10GBASE-LR" there.
EX4200 12.3R6: > show interfaces diagnostics optics xe-2/1/0 Physical interface: xe-2/1/0 Optical diagnostics : N/A > show chassis pic fpc-slot 2 pic-slot 1 FPC slot 2, PIC slot 1 information: Type 2x 10GE SFP+ State Online PIC version 1.7 Uptime 3 days, 18 hours, 19 minutes, 38 seconds PIC port information: Fiber Xcvr vendor Wave- Xcvr Port Cable type type Xcvr vendor part number length Firmware 0 unknown cable n/a INTEGRA NETWORKS SFPP-C51-80-10GD 1510 nm 0.0 Item Version Part number Serial number Description Xcvr 0 UNKNOWN EOSExxxxxxxx UNKNOWN MX960 11.4R8: # run show interfaces diagnostics optics xe-2/0/3 Physical interface: xe-2/0/3 Laser bias current : 75.402 mA Laser output power : 1.1290 mW / 0.53 dBm Module temperature : 43 degrees C / 109 degrees F Module voltage : 3.2470 V Receiver signal average optical power : 0.0317 mW / -14.99 dBm Laser bias current high alarm : Off Laser bias current low alarm : Off Laser bias current high warning : Off Laser bias current low warning : Off Laser output power high alarm : Off Laser output power low alarm : Off Laser output power high warning : Off Laser output power low warning : Off Module temperature high alarm : Off Module temperature low alarm : Off Module temperature high warning : Off Module temperature low warning : Off Module voltage high alarm : Off Module voltage low alarm : Off Module voltage high warning : Off Module voltage low warning : Off Laser rx power high alarm : Off Laser rx power low alarm : Off Laser rx power high warning : Off Laser rx power low warning : Off Laser bias current high alarm threshold : 120.000 mA Laser bias current low alarm threshold : 30.000 mA Laser bias current high warning threshold : 110.000 mA Laser bias current low warning threshold : 35.000 mA Laser output power high alarm threshold : 5.0110 mW / 7.00 dBm Laser output power low alarm threshold : 0.6310 mW / -2.00 dBm Laser output power high warning threshold : 3.9810 mW / 6.00 dBm Laser output power low warning threshold : 0.7940 mW / -1.00 dBm Module temperature high alarm threshold : 90 degrees C / 194 degrees F Module temperature low alarm threshold : -15 degrees C / 5 degrees F Module temperature high warning threshold : 85 degrees C / 185 degrees F Module temperature low warning threshold : -10 degrees C / 14 degrees F Module voltage high alarm threshold : 3.600 V Module voltage low alarm threshold : 3.000 V Module voltage high warning threshold : 3.500 V Module voltage low warning threshold : 3.050 V Laser rx power high alarm threshold : 0.1585 mW / -8.00 dBm Laser rx power low alarm threshold : 0.0013 mW / -28.86 dBm Laser rx power high warning threshold : 0.1259 mW / -9.00 dBm Laser rx power low warning threshold : 0.0016 mW / -27.96 dBm # run show chassis pic fpc-slot 2 pic-slot 0 FPC slot 2, PIC slot 0 information: Type 4x 10GE(LAN) SFP+ State Online PIC version 0.0 Uptime 82 days, 5 hours, 45 minutes, 19 seconds PIC port information: Fiber Xcvr vendor Port Cable type type Xcvr vendor part number Wavelength 0 10GBASE LR SM FINISAR CORP. FTLX1471D3BNL-J1 1310 nm 1 10GBASE LR SM FINISAR CORP. FTLX1471D3BNL-J1 1310 nm 2 10GBASE LR SM FINISAR CORP. FTLX1471D3BNL-J1 1310 nm 3 UNKNOWN CABLE n/a INTEGRA NETWORKS SFPP-C51-80-10GD 1510 nm Item Version Part number Serial number Description Xcvr 3 NON-JNPR EOSExxxxxxxx UNSUPPORTED _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp