Hi Uwe, Uwe Dippel wrote: > [...] > # dladm scan-wifi rum1 > LINK ESSID BSSID/IBSSID SEC STRENGTH MODE > SPEED > rum1 wlan 0:13:10:7c:aa:f1 wpa excellent g 54Mb > rum1 aztech 0:12:e:82:cd:99 wep excellent g 54Mb > # ifconfig -a > lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 > index 1 > inet 127.0.0.1 netmask ff000000 > rge0: flags=201004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4,CoS> mtu 1500 > index 2 > inet 192.168.116.61 netmask ffffff00 broadcast 192.168.116.255 > ether 0:e0:4d:30:2d:68 > rum1: flags=201000842<BROADCAST,RUNNING,MULTICAST,IPv4,CoS> mtu 1500 index 3 > inet 0.0.0.0 netmask 0 > ether 0:21:27:c0:a8:9b > lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 > index 1 > inet6 ::1/128 > # ifconfig rum1 plumb > ifconfig: SIOCSLIFNAME for ip: rum1: already exists > # ifconfig rum1 dhcp > It seems you don't use it correctly, you need to connect to a AP first. Please try:
# svcs -a | grep nwam --> see nwam is enable or not? it should be disabled. # dladm create-secobj -c wpa psk ............input your key------------ # dladm connect-wifi -e wlan -k psk rum1 # ifconfig rum1 dhcp Then, it should work for you. -- Quaker > # ifconfig -a > lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 > index 1 > inet 127.0.0.1 netmask ff000000 > rge0: flags=201004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4,CoS> mtu 1500 > index 2 > inet 192.168.116.61 netmask ffffff00 broadcast 192.168.116.255 > ether 0:e0:4d:30:2d:68 > rum1: flags=201004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4,CoS> mtu 1500 > index 3 > inet 192.168.116.198 netmask ffffff00 broadcast 192.168.116.255 > ether 0:21:27:c0:a8:9b > lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 > index 1 > inet6 ::1/128 > # ping 192.168.116.100 > no answer from 192.168.116.100 > > # ping 192.168.116.198 > 192.168.116.198 is alive > # netstat -rn > > Routing Table: IPv4 > Destination Gateway Flags Ref Use Interface > -------------------- -------------------- ----- ----- ---------- --------- > default 192.168.116.200 UG 1 0 rge0 > default 192.168.116.200 UG 1 0 rum1 > 192.168.116.0 192.168.116.61 U 1 155 rge0 > 192.168.116.0 192.168.116.198 U 1 0 rum1 > 127.0.0.1 127.0.0.1 UH 1 146 lo0 > > Routing Table: IPv6 > Destination/Mask Gateway Flags Ref Use If > > --------------------------- --------------------------- ----- --- ------- > ----- > ::1 ::1 UH 1 21 lo0 > > # ping 192.168.116.200 > no answer from 192.168.116.200 > > Then I plugged back the wired LAN, and > > # ping 192.168.116.200 > 192.168.116.200 is alive > > There are some items here that look strange: > 1. The initial scan did not work > 2. plumb did not give it an IP > 3. It did not allow to ping its gateway > (4. nwam is still not working for it) > > > Uwe >
