Looks like the disk is failing or queueing is not working right. As for ACPI, not working is common, that's not an error, merely a warning as it says. Maybe someone here responsible for disk drivers can answer what exactly this means. David, is this notebook using a SATA disk, and does it run native under other operating systems?
James On Dec 2, 2007, at 9:02 AM, Dr. David Kirkby wrote: > Since the very first time I booted Solaris Express Developer Edition > 9/07 snv_70b X86 on this laptop (Sony VAIO VGN-Sz4XWN/C) there has > been a long delay in the boot process. The messages indicate > something is amiss, but since it has done this all the time, and it > boots OK, I'm not sure how much I should concern myself with it. See > below. Its the last 20 or so lines where the problems occur, but I > have pasted the very first line from boot, rather than omit > something that might be useful. > > Dec 2 09:42:45 kingfisher pci_autoconfig: [ID 466951 kern.warning] > WARNING: No ACPI obj for bus1, ACPI OFF? > Dec 2 09:42:45 kingfisher pci_autoconfig: [ID 769584 kern.warning] > WARNING: detected unsupported configuration: non-empty bridge (bus > 0x0, dev 0x1c, func 0x1) without I/O resources assigned by bios for > secondary bus 0x6 > Dec 2 09:42:45 kingfisher pci_autoconfig: [ID 130646 kern.warning] > WARNING: devices under bridge bus 0x0, dev 0x1c, func 0x1 will not > be assigned I/O ports > > Dec 2 09:43:26 kingfisher scsi: [ID 107833 kern.warning] WARNING: / > pci at 0,0/pci-ide at 1f,2/ide at 0 (ata2): > Dec 2 09:43:26 kingfisher timeout: abort request, target=0 lun=0 > Dec 2 09:43:26 kingfisher scsi: [ID 107833 kern.warning] WARNING: / > pci at 0,0/pci-ide at 1f,2/ide at 0 (ata2): > Dec 2 09:43:26 kingfisher timeout: abort device, target=0 lun=0 > Dec 2 09:43:26 kingfisher scsi: [ID 107833 kern.warning] WARNING: / > pci at 0,0/pci-ide at 1f,2/ide at 0 (ata2): > Dec 2 09:43:26 kingfisher timeout: reset target, target=0 lun=0 > Dec 2 09:43:26 kingfisher scsi: [ID 107833 kern.warning] WARNING: / > pci at 0,0/pci-ide at 1f,2/ide at 0 (ata2): > Dec 2 09:43:26 kingfisher timeout: reset bus, target=0 lun=0 > Dec 2 09:43:27 kingfisher scsi: [ID 107833 kern.warning] WARNING: / > pci at 0,0/pci-ide at 1f,2/ide at 0 (ata2): > Dec 2 09:43:27 kingfisher timeout: early timeout, target=0 lun=0 > Dec 2 09:43:27 kingfisher gda: [ID 107833 kern.warning] WARNING: / > pci at 0,0/pci-ide at 1f,2/ide at 0/cmdk at 0,0 (Disk0): > Dec 2 09:43:27 kingfisher Error for command 'read sector' > Error Level: Informational > Dec 2 09:43:27 kingfisher gda: [ID 107833 kern.notice] > Sense Key: aborted command > Dec 2 09:43:27 kingfisher gda: [ID 107833 kern.notice] > Vendor 'Gen-ATA ' error code: 0x3 > Dec 2 09:43:27 kingfisher gda: [ID 107833 kern.warning] WARNING: / > pci at 0,0/pci-ide at 1f,2/ide at 0/cmdk at 0,0 (Disk0): > Dec 2 09:43:27 kingfisher Error for command 'read sector' > Error Level: Informational > Dec 2 09:43:27 kingfisher gda: [ID 107833 kern.notice] > Sense Key: aborted command > Dec 2 09:43:27 kingfisher gda: [ID 107833 kern.notice] > Vendor 'Gen-ATA ' error code: 0x3 > > This message posted from opensolaris.org > _______________________________________________ > laptop-discuss mailing list > laptop-discuss at opensolaris.org
