a very good little mill the revo in some ways better than the 900 I some
times wonder why the sale of them never really took off
with smaller work under 6 inches dia and under 3 foot long I keep coming
back to it over the 900 mill.
a good idea Tim I own a vertical vise from legacy if you ever need pics or
measurements
Bill
----- Original Message -----
From: "Tim Krause" <artmarb...@comcast.net>
To: <legacy-ornamental-mills@googlegroups.com>
Sent: Sunday, November 06, 2011 1:44 PM
Subject: Re: Vertical Mounting Brackets
When I used it, I was adding some dovetail slots to table legs. I clamped
the legs to wood and cut the angles in both sides of the leg. This was
using the y axis travel. It was similar to what was being used on the revo
at the time. http://legacywoodworking.com/class.cfm?id=42 except they had
theirs setup on the x-axis. I don't have the jig near me or I would set it
up and show you what I did.
-Tim
----- Original Message -----
From: "begatbrown" <darylmichaelsc...@gmail.com>
To: "Legacy Ornamental Mills" <legacy-ornamental-mills@googlegroups.com>
Sent: Saturday, November 05, 2011 4:01 PM
Subject: Re: Vertical Mounting Brackets
Tim,
I think I have the concept, but I'd like to see the set up and know
what you did and could use them to do.
Begat
On Nov 5, 4:56 pm, "Tim Krause" <artmarb...@comcast.net> wrote:
Hello All,
A long time ago I made these brackets. I don't think I ever showed them to
the group since they where just a quick solution to a problem I had at the
time.
They mounted to the inside of the inner rails. A board connects the two
and they form a poorman's version of the vertical vises Legacy was selling
at the time. I just clamped my stock to the wood connecting piece. They did
the job but they were slow to setup and remove. I was using Legacy's large
square tabs to mount them to the inner side of the inner rails. I had to
unscrew them to remove the brackets. I've been thinking there is a better
way to do this and I've come up with this drawing.
It still uses a board to connect the two but I'm going to add 1/4-20
threaded inserts to mount the board to (not shown). The mounts will use my
HD mounts (1/4-20) for the narrow side rails and location tabs (not shown
bent) will instantly align the brackets square. They are 4" in total depth
so they will work on the bench models. Is this a useful idea?
-Tim
brackets_pre.jpg
17KViewDownload
new_vertical_mounting_brackets.jpg
24KViewDownload
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To post to this group, send email to
legacy-ornamental-mills@googlegroups.com.
To unsubscribe from this group, send email to
legacy-ornamental-mills+unsubscr...@googlegroups.com.
For more options, visit this group at
http://groups.google.com/group/legacy-ornamental-mills?hl=en.
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To post to this group, send email to
legacy-ornamental-mills@googlegroups.com.
To unsubscribe from this group, send email to
legacy-ornamental-mills+unsubscr...@googlegroups.com.
For more options, visit this group at
http://groups.google.com/group/legacy-ornamental-mills?hl=en.
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2012.0.1869 / Virus Database: 2092/4598 - Release Date: 11/05/11
--
You received this message because you are subscribed to the Google Groups "Legacy
Ornamental Mills" group.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
To unsubscribe from this group, send email to
legacy-ornamental-mills+unsubscr...@googlegroups.com.
For more options, visit this group at
http://groups.google.com/group/legacy-ornamental-mills?hl=en.
