now i understand, hahahahaha
On Thu, May 17, 2012 at 8:55 PM, Tim Krause <artmarb...@comcast.net> wrote: > ** > One last plan. I've attached a pdf that shows the exact dimensions to cut > your staves to. It will create an 8" column. > > -Tim > > > ----- Original Message ----- > *From:* Tim Krause <artmarb...@comcast.net> > *To:* legacy-ornamental-mills@googlegroups.com > *Sent:* Thursday, May 17, 2012 6:35 PM > *Subject:* Re: could someone explain the formula > > Ok, It's picture time. :-) > > The version on the left is a correct birdsmouth joint as Mike was > describing. Your version cut the 90 degree angle in the wrong face as > shown on the right. > > -Tim > > > ----- Original Message ----- > *From:* James Edgell <jdm...@gmail.com> > *To:* legacy-ornamental-mills@googlegroups.com > *Sent:* Thursday, May 17, 2012 6:15 PM > *Subject:* Re: could someone explain the formula > > you lost me, if you go look at the magnate site they show a bit that cuts > a 45 degree angle and with 8 pieces forms a 8 piece column, so using their > formula , with 2 inch thick wood, with a 2 inch cut depth on each side of > the cut, i need 3 and three eights width across the board to form an 8 inch > diameter column, i did that and that is what i ended up with, only giving a > little better than 6 inches in diameter for the diameter for the column > once it is turned to round . still not sure what i did wrong? > > On Thu, May 17, 2012 at 7:50 PM, Tim Krause <artmarb...@comcast.net>wrote: > >> ** >> Is it safe to say that you understand now where you went wrong? Your >> version is a pretty cool variation! >> >> -Tim >> >> >> >> >> ----- Original Message ----- >> *From:* James Edgell <jdm...@gmail.com> >> *To:* legacy-ornamental-mills@googlegroups.com >> *Sent:* Thursday, May 17, 2012 1:11 PM >> *Subject:* Re: could someone explain the formula >> >> yea i thought it looked pretty cool also, something for future fantasy >> projects, hahaha >> >> >> >> >> -- >> You received this message because you are subscribed to the Google >> Groups "Legacy Ornamental Mills" group. >> To post to this group, send email to >> legacy-ornamental-mills@googlegroups.com. >> To unsubscribe from this group, send email to >> legacy-ornamental-mills+unsubscr...@googlegroups.com. >> For more options, visit this group at >> http://groups.google.com/group/legacy-ornamental-mills?hl=en. >> > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > To unsubscribe from this group, send email to > legacy-ornamental-mills+unsubscr...@googlegroups.com. > For more options, visit this group at > http://groups.google.com/group/legacy-ornamental-mills?hl=en. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > To unsubscribe from this group, send email to > legacy-ornamental-mills+unsubscr...@googlegroups.com. > For more options, visit this group at > http://groups.google.com/group/legacy-ornamental-mills?hl=en. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > To unsubscribe from this group, send email to > legacy-ornamental-mills+unsubscr...@googlegroups.com. > For more options, visit this group at > http://groups.google.com/group/legacy-ornamental-mills?hl=en. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en.
<<bad_birdsmouth_joint.jpg>>