Good advice Jon...I was thinking along those lines about about stability regarding cup and bow but just needed to hear it from someone else. Thanks for responding. Lou
On Friday, August 18, 2017 at 12:02:58 PM UTC-4, Jon Preston wrote: > I would not make these from solid pieces of 8/4 oak with the grain > oriented perpendicular to the axis of the column. They will cup, warp, bow > and shrink. It wont last. Make the entire piece from a circle of glued > wedges. 12 wedges (long grain in the axis of the column) in 30 degree > increments will give a much better and long lasting result. Just glue them > up with titebond III and some band clamps. > > > > Sent from my Verizon, Samsung Galaxy smartphone > > -------- Original message -------- > From: MAX LATHAM <ma...@hotmail.com <javascript:>> > Date: 8/18/17 11:54 AM (GMT-05:00) > To: legacy-orna...@googlegroups.com <javascript:> > Subject: Re: Porch Column Base > > > > Get the three set birds mouth bits, roll up the column and mill it! > > max > ------------------------------ > *From:* legacy-orna...@googlegroups.com <javascript:> < > legacy-orna...@googlegroups.com <javascript:>> on behalf of Lou Lossi < > louis...@gmail.com <javascript:>> > *Sent:* Friday, August 18, 2017 10:13 AM > *To:* Legacy Ornamental Mills > *Subject:* Porch Column Base > > > I’ve been asked by a friend to make three column bases to replace rotted > ones for a front porch and had a few questions for the knowledgeable folks > on this site. I have not been out to the property to inspect but the > homeowner sent a drawing and pic with measurements for me and I hope I can > do it on my LOM. The base is 15” square on the bottom, 14” round the next > tier up, and 13” round above that. Each tier is 1.5” thick resulting in a > total height of 4.5” tall. I suggested using white oak for its durability > and strength and found some 8/4 at my local lumber supplier that could be > milled down to the 1.5” tiers. Since I do not have a lathe, I had planned > on making these solid and routing the profile edges with the LOM rotary > table then gluing each of the three pieces up for the completed base. After > reading the posts here regarding columns and bases, I’m seeing bases that > are hollow in the inside. Would I be subject to any issues if I left them > solid and just glued them up? I was going to use Titebond III for the glue. > Would I need to screw and glue or even dowel them for added strength? > Instead of 1.5” thick for each tier, should I perhaps glue up ¾” pieces to > make profiling the edges a little easier? I’m in the process of making a > mock up just using 1.5” pine to see how things go to see if I can handle > this. The homeowner is hoping I can get it close to the existing ones just > going by the pics, but if all goes well after the mock up, I will visit the > property to get a complete accurate profile. > > I know Mike Pung has done a ton of these and reading his posts has > inspired me to give this a shot. Any and all suggestions and opinions are > gladly accepted from those who have any experience attempting these. > > Thanks in advance, > > Lou > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com > <javascript:>. > To post to this group, send email to legacy-orna...@googlegroups.com > <javascript:>. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
