Oh yes i just buy stick on rules off ebay http://www.ebay.co.uk/itm/150cm-Vinyl-Silver-Self-Adhesive-Measuring-Tape-Ruler-Sticker-Sewing-sguk-LD-/252779101631?epid=582325546 <http://www.ebay.co.uk/itm/150cm-Vinyl-Silver-Self-Adhesive-Measuring-Tape-Ruler-Sticker-Sewing-sguk-LD-/252779101631?epid=582325546&hash=item3adacefdbf:g:fH8AAOSwCGVX4uui> &hash=item3adacefdbf:g:fH8AAOSwCGVX4uui
Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Bill Bulkeley Sent: Thursday, 7 September 2017 2:58 PM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Dovetails Been a long time since I cut dovetails with the revo and I only did one, from memory I followed legacys idea in the training (see attachment ) and used the keller dovetail template instead of legacys.but it is easier to do the dovetail joints on the router table with the keller dovetail template than on the revo so i haven’t done one since on the legacy. Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Richard Ellis Sent: Wednesday, 6 September 2017 8:46 PM To: Legacy Ornamental Mills Subject: Dovetails I have a Revo, and have been cutting box (finger ) joints using Mike's indexing method, 3/8" up-cutting two flute spiral milling cutter. I have been very surprised at the accuracy of the joints. One thing I did do was to change the crank handle over -top to bottom- when doing the mating piece as I found out to hold it in a vertical position was more difficult than holding it down However I want to do some dovetails I have no templates how do I go about it?? The pins are easy, it's the mating part. That I am not too sure about. Roger, How many Revo's are in there in the u.k. and can one still get the stick on measure tape for the Revo, the long one?? Richard -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. _____ <http://www.avg.com/internet-security> AVG logo This email has been checked for viruses by AVG antivirus software. www.avg.com <http://www.avg.com/internet-security> -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.