guess gear it up lol I do have access to many different gear motors if anyone really wants to find one lol. Kind Regards,
Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Mon, Feb 15, 2021 at 11:19 PM <bulke...@mmnet.com.au> wrote: > Already looked at that mac the rpm is too slow lol > > > > Bill > > > > *From:* legacy-ornamental-mills@googlegroups.com < > legacy-ornamental-mills@googlegroups.com> *On Behalf Of *M.W.Foscue > *Sent:* Tuesday, 16 February 2021 3:54 PM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* Re: Looking for some new projects. > > > > Curtis, > > Thanks for sharing. > > Very interesting product video. Like Bill, I'd never heard of a corn > kernel fired heater/boiler. Pellet stoves - yes; corn fired? - no. > > I bet both Tim Z and Joe B. are going to contact that Maxim heater/boiler > company to discuss buying a couple of those auger drive motors (540 in/lbs > of torque!) to install on their LOMs! Bill would too if the S&H weren't so > high. > > LoL! > > Mac > ------------------------------ > > -----Original Message----- > From: 'Curt George' via Legacy Ornamental Mills > Sent: Feb 15, 2021 9:55 PM > To: "legacy-ornamental-mills@googlegroups.com" > Subject: Re: Looking for some new projects. > > Bill a corn burner is very much like a pellet burner. the corn is shucked > into small cornels, those cornels are then burned as a source of fuel. A > wood pellet burner works along the same lines. When fuel runs scarce you > need to find a new source of heat when its cold out. > > In the US large amounts of corn are not used for other products, (for a > number of reasons.) burning corn that is for most context, waist products. > in these areas, Corn is cheaper then wood, coal, or natural gas. > https://www.youtube.com/watch?v=pYtNJCmKHjs YouTube has a lot of videos > on this topic. > > > > Stay warm/cool EVERYONE. > > Now back to the Legacy topics. ;-) > > > > Thank you. > > > > C.A.G. > ------------------------------ > > On Monday, February 15, 2021, 06:52:55 PM EST, <bulke...@mmnet.com.au> > wrote: > > > > Ps flooding with lube also helps with chip removal its better than blowing > a mess every where with air. When cutting,… wood and metal don’t go very > well together unless you use a sacrificial piece of wood the cutting fluid > destroys the mdf. > ------------------------------ > > *From:* legacy-ornamental-mills@googlegroups.com < > legacy-ornamental-mills@googlegroups.com> *On Behalf Of * > bulke...@mmnet.com.au > *Sent:* Tuesday, 16 February 2021 9:39 AM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* RE: Looking for some new projects. > > > > I don’t know much about cnc cutting of aluminium but I did machine it in > the old days when I was an engineer machinist. I do know cutting lubricant > was paramount the best I found believe it or not was wd 40. cutting it dry > or with only a little lubricant the aluminium would build up on the cutter, > tool or drill and cause it to jam and break, flooding the tool was the best > it usually cut very well that way as for feed rate that depended on the cut > light cuts you could go faster heaver cuts slower as with any machining now > after saying all that I have never milled aluminium with a bit as small as > 1/8 but the principle would be the same I would think. > > Just my 2 cents worth maybe it will help > > > > Bill > ------------------------------ > > *From:* legacy-ornamental-mills@googlegroups.com < > legacy-ornamental-mills@googlegroups.com> *On Behalf Of *Harvey Matyas > *Sent:* Tuesday, 16 February 2021 2:35 AM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* Re: Looking for some new projects. > > > > Bill > > > > I have a Shark HD3. I was using a 1/8 inch router bit. Before every cut, > I used some threading oil that I placed on the Aluminum. > > I used my compressor to blow air at the router bit to clear chips and > help to cool the bit. The chips that I created were too small, for my next > cut, I intend to speed up > > the travel from 20 inch per minute to 30 or 40 inches per minute. My > router speed was at 10,000 rpm and I don't know if I should > > speed if up or not. I'm watching a lot of videos on speeds and feeds. * It > creates a mess with the aluminum chips. I plan on making like* > > *a 1 or 2 inch fence around the piece to try to keep the waste in one > place.* > > *I was thinking about getting a mister, but after talking with someone > familiar with cutting metal with a mister said that it creases a mess and > not to let it hit MDF and* > > *to have the place properly ventilated. My spoilboard is MDF and my > basement have 3 windows that I really don't open.* > > > > *Any advice on cutting aluminum would be greatly appreciated.* > > > > *Take care,* > > > > *Harvey* > ------------------------------ > > On Mon, Feb 15, 2021 at 7:21 AM <bulke...@mmnet.com.au> wrote: > > Harvey may I ask what machine were you using to cut your 5 3/3 circle > > > > Bill > ------------------------------ > > *From:* legacy-ornamental-mills@googlegroups.com < > legacy-ornamental-mills@googlegroups.com> *On Behalf Of *Tim Ziegler > *Sent:* Monday, 15 February 2021 11:39 PM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* Re: Looking for some new projects. > > > > Good morning Harvey, > > > > Yea great to have you here and I'm pretty sure everyone will continue to > welcome all your input and presence. > > So with the bit slipping or what ever may have happened I was running an > angle on my LOM 1200 here a week ago > > and my clamping failed right toward the tail end of the milling and of > course the damage went beyond being > > able to save the transition thresh hold. I wrecked the piece but not the > bit. The bit vibrated so much that, that's what > > caused my problem. > > Sounds like yours was a little different mishap but seems this does happen > from time to time. I was spinning a large > > 1 1/2 dia. older bit. > > I finished to next transition strip on the table saw. customer needed it > asap and I was't taking chances until I had > > a better bit and clamping design. > > > Kind Regards, > > > > Timothy J. Ziegler > ------------------------------ > > On Sun, Feb 14, 2021 at 9:34 PM Harvey Matyas <hmatyas0...@gmail.com> > wrote: > > Hi Tim > > > > I hope to follow this group as long as they will let me. > > I know the weather is a pain, I went into my workshop and walked out > again, It was that cold in the basement. > > Someone approached me to cut some aluminum for him. On a test piece, I > broke 2 1/8 inch bits before I > > finally started getting it cut through. Looking at what happened, I was > cutting conservatively. I was cutting a 5 3/8 inch circle in 1/8 inch > alum. I was cutting 0.01 inches at a time. I think when the bit broke, > instead of .01 I went .1 inches. I can't check, but I think this happened > because the first 45 degrees was cut through, the rest took about 10 more > tries. Either that or the bit dropped down and started cutting that deep. > > > > If I cut the circle for this guy, he may also want me to start cutting out > signs. He does something with fabic > > > > Harvey Matyas > ------------------------------ > > On Sunday, February 14, 2021, 09:00:54 PM CST, Tim Ziegler < > timjzieg...@gmail.com> wrote: > > > > Hey Harvey hope all is well good to see your still following. > > Suppose to hit 30 below here tonight. wow what a long cold snap. > > > Kind Regards, > > > > Timothy J. Ziegler > ------------------------------ > > On Sun, Feb 14, 2021 at 8:30 PM Harvey Matyas <hmatyas0...@gmail.com> > wrote: > > Hi Curt > > > > You already probably know about this guy but here goes. > > > > Projects Archives | Turning for Profit | Woodturning | Lathe | > <https://www.turningforprofit.com/plans/> > > > > He has like a user group where he periodically sends out emails that have > projects in them. > > > > I hope this helps, keep warm. > > > > Harvey > ------------------------------ > > On Sun, Feb 14, 2021 at 8:21 PM 'Curt George' via Legacy Ornamental Mills < > legacy-ornamental-mills@googlegroups.com> wrote: > > HI everyone. > > > > I hope everyone is well? > > > > Its COLD in my shop, So I spent most of my day staying inside. I've been > > looking for projects to play with on the Legacy and or my Lathe. On the > internet today. > > > > I want to do some more bone turning, I have already cut out a number of > bone disks, I am looking forward to gluing them up into something that I > can turn, soon. > > The problem is What should I make? > > I don't like pen's! > > I have already made a number of magnify glass's and other kits type of > projects. > > > > I have gone to a number of dollar stores and hardware and thrift stores, > looking for cheaply made things that can be re-worked. but so far no luck > finding anything new. > > So I thought I would ask you all. Dose anyone know of a nice projects, > that you like to make? Family heirloom type of stuff. Perhaps a letter > opener? or ??? > > > > Any and all ideas are welcome. > > > > Looking forward to talking to you all more. > > > > Have a good night. > > > > C.A.G. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/454972608.5504.1613451243916%40wamui-gaston.atl.sa.earthlink.net > <https://groups.google.com/d/msgid/legacy-ornamental-mills/454972608.5504.1613451243916%40wamui-gaston.atl.sa.earthlink.net?utm_medium=email&utm_source=footer> > . > > > <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> > Virus-free. > www.avast.com > <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> > <#m_-579864263673419152_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2> > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/000201d70423%24533ea5a0%24f9bbf0e0%24%40mmnet.com.au > <https://groups.google.com/d/msgid/legacy-ornamental-mills/000201d70423%24533ea5a0%24f9bbf0e0%24%40mmnet.com.au?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLH80Q23pW8Fnr0UG8JR08W4Psmu0PQ%2BFb3farydcprdng%40mail.gmail.com.