Hi Dan Not at this moment. the styles is solidly mounted, 1/2" rod. Latter I do plan to make other adaptors to cover a wide range of bits. but at this time, its what you see is what you get. For the time being, I plan to add details to the work like roping on a curve and fluting. As I see it, the styles is just a pointer or a limit to where the router can and can not go. (I do know that its more then that. But as least for the time being, this is my starting place or point, and not the finish-line to this concept. I'm a long way form being done with this. ) ;-) thank you. C.A.G. On Saturday, June 4, 2022, 06:25:38 PM EDT, <bulke...@mmnet.com.au> wrote: <!--#yiv3979448487 _filtered {} _filtered {} _filtered {}#yiv3979448487 #yiv3979448487 p.yiv3979448487MsoNormal, #yiv3979448487 li.yiv3979448487MsoNormal, #yiv3979448487 div.yiv3979448487MsoNormal {margin:0cm;font-size:11.0pt;font-family:"Calibri", sans-serif;}#yiv3979448487 a:link, #yiv3979448487 span.yiv3979448487MsoHyperlink {color:blue;text-decoration:underline;}#yiv3979448487 span.yiv3979448487EmailStyle19 {font-family:"Arial", sans-serif;color:windowtext;}#yiv3979448487 .yiv3979448487MsoChpDefault {font-size:10.0pt;} _filtered {}#yiv3979448487 div.yiv3979448487WordSection1 {}--> Looks great curt, do you have a way of changing styles dia to match the dia of the router bit your using?
Bill From: 'Curt George' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com> Sent: Sunday, 5 June 2022 7:28 AM To: Legacy ornamental mills <legacy-ornamental-mills@googlegroups.com> Subject: New Front mounted template follower Hello everyone. It may not looks like much. but I finally got my template follower to work. Its rock solid, fully adjustable, and holds 1/4" templates well. The trick to use the template follower on the Legacy that I have found, is to have the template follower only control the Y axis, and the X axis is moved by the acme screw/ motor to move the carriage. Legacy design was to have the follower in the back of the machine, I found in the past, it was much easer to control the template movement if the follower was in front of the machine. Since I re-designed my machine, a few years ago. I needed to change and adapt the follower so it again could be used on my Legacy. So Yes a template follower in front can and will get in the way when not needed So I made this, follower is easy to remove and quick to re-install when needed. so now you see it, latter you wont. ;-) This may not be for everyone, but it just might help others in our group to start thinking? There are lots of possibility's out there for using a template with the Legacy. More latter. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/955395991.4017486.1654378103723%40mail.yahoo.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000a01d87861%24ffce2350%24ff6a69f0%24%40mmnet.com.au. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/2014002569.752003.1654382934932%40mail.yahoo.com.