Hey Curt, Yup sounds like a good Sunday afternoon project. Have a good night. I played on my REVO HYBRID EXT tonight. nothing fancy but turned a spindle no less just because I had the bug lol .
Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Sat, Jun 4, 2022 at 9:39 PM 'Curt George' via Legacy Ornamental Mills < legacy-ornamental-mills@googlegroups.com> wrote: > Hi Tim > > My goal is to make this styles/guide pin, so it will have another pin > screwed in the center, where then other sized bearings or bushing can be > mounted on to it, giving me different sizes of followers to match the > router bits dia. sorta like a multi stepped router bit. > > I have made many of my templates with the center line on the template, the > idea is to line up the center line of the template with the center line of > the Legacy. by lining up the two centers should make it easy to keep > everything uniformed. My bigger problem now is finding more side cutting > router bit for the work I want to make. "O"Well that's a problem for > tomorrow. ;-) > > Have a good night. > > C.A.G. > > On Saturday, June 4, 2022, 10:20:01 PM EDT, Tim Ziegler < > timjzieg...@gmail.com> wrote: > > > pretty innovative Curt, Now if you did a step tracing pin similar to what > you did but add 3 or 4 steps you would be even more > diverse in different width bits. Or of course have more then one tracing > pin at different sizes. > > Kind Regards, > > Timothy J. Ziegler > Ziegler WoodWork & Specialty > 14171 160th Ave. > Foreston MN 56330 > > 320-294-5798 shop > 320-630-2243 cell > > > On Sat, Jun 4, 2022 at 4:28 PM 'Curt George' via Legacy Ornamental Mills < > legacy-ornamental-mills@googlegroups.com> wrote: > > Hello everyone. > It may not looks like much. but I finally got my template follower to > work. Its rock solid, > fully adjustable, and holds 1/4" templates well. > > The trick to use the template follower on the Legacy that I have found, is > to have the template follower only control the Y axis, and the X axis is > moved by the acme screw/ motor to move the carriage. > > Legacy design was to have the follower in the back of the machine, I found > in the past, it was much easer to control the template movement if the > follower was in front of the machine. Since I re-designed my machine, a > few years ago. I needed to change and adapt the follower so it again could > be used on my Legacy. > > So Yes a template follower in front can and will get in the way when not > needed So I made this, follower is easy to remove and quick to re-install > when needed. so now you see it, latter you wont. ;-) > > This may not be for everyone, but it just might help others in our group > to start thinking? > There are lots of possibility's out there for using a template with the > Legacy. > > More latter. > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/955395991.4017486.1654378103723%40mail.yahoo.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/955395991.4017486.1654378103723%40mail.yahoo.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLHWvbQVCgpL1MhNxTz5jexu%2BhAT63auouafEBC%2BUqyBaw%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLHWvbQVCgpL1MhNxTz5jexu%2BhAT63auouafEBC%2BUqyBaw%40mail.gmail.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/1480965766.4045046.1654396789948%40mail.yahoo.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/1480965766.4045046.1654396789948%40mail.yahoo.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFVPJpWAcb8y_tNE7ok5aN9jYG2GwCXP2CusEc%2BETB%2Bug%40mail.gmail.com.
