Larry,
What does your route table look like at that point? "route -n" will tell
you. You'll need to see a default gateway entry:
Destination Gateway Genmask Flags Metric Ref Use
Iface
130.175.138.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
0.0.0.0 130.175.138.1 0.0.0.0 UG 0 0 0 eth0
^^
^^
^^
Mark
-----Original Message-----
From: Larry Heath [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, April 10, 2002 2:21 PM
To: [EMAIL PROTECTED]
Subject: RedHat 7.2 31-bit w/IBM LCS - another problem
HELP again! The telnet session (and ping) times out trying to reach this IP
addr 205.213.113.123.
Below are pieces of the console log (HMC) for the Linux LPAR where I'm
trying to boot rh72 w/lcs.
---------- snipped ------------
Starting the zSeries initrd to configure networking. Version is 0.49
Starting lcs module $Revision: 1.120.2.6 $ $Date: 2002/03/01 16:51:06 $
with chandev support,with multicast support, with ethernet support, with
token ring support.
debug: reserved 16 areas of 2 pages for debugging lcs
debug: lcs: new level 0
eth0: ip v6 supported no enabled no
eth0: multicast supported yes enabled yes
lcs: eth0 configured as follows read subchannel=1c69 write subchannel=1c6a
read_devno=6a0a write_devno=6a0b
hw_address=00:06:29:EC:F2:97 rel_adapter_no=0
eth0 Link encap:Ethernet HWaddr 00:06:29:EC:F2:97
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo
Starting portmap.
-------- snipped dasd stuff -----------
Starting telnetd and sshd to allow login over the network.
Please connect now to 205.213.113.123
and start 'loader' from this shell.#
--------------
--------------
Here is the parmline which is on one line on the tape but displayed here as
pieces.
root=/dev/ram0 ro ip=off DASD=1702,1726
HOST=linux2.shawind.com:eth0:205.213.113.123:1500
NETWORK=205.213.113.0:255.255.255.0:205.213.113.255:205.213.113.254
DNS=172.31.249.190 SEARCHDNS=shawind.com
CHANDEV=noauto;lcs0,0x6a0a,0x6a0b chandev=noauto;lcs0,0x6a0a,0x6a0b
We are able to access these device addresses when we boot the Marist 2.2
linux so we know that the devices and addresses work. Is there a another
problem in my parms?
Thanks...... Larry
**********************************************************
Privileged and/or confidential information may be contained in this message.
If you are not the addressee indicated in this message (or are not
responsible for delivery of this message to that person) , you may not copy
or deliver this message to anyone. In such case, you should destroy this
message and notify the sender by reply e-mail.
If you or your employer do not consent to Internet e-mail for messages of
this kind, please advise the sender.
Shaw Industries, Inc. does not provide or endorse any opinions, conclusions
or other information in this message that do not relate to the official
business of the company.
**********************************************************
