Jeff Garzik wrote:
Tejun Heo wrote:
Hello, Jeff.
Jeff Garzik wrote:
Tejun Heo wrote:
Hello, Jeff and Albert.
This patchset fixes the following race.
(port A has ATA device and B ATAPI).
port B : ata_issue_prot() (ATAPI_NODATA)
port B : packet_task scheduled
port A : ata_issue_prot() (DMA)
intr : ata_interrupt()
port A : ata_host_intr -> this is all good & dandy
port B : ata_host_intr -> finishes ATAPI cmd w/ error (request
sense)
This is where the race is, we're polling for port B's qc, we must not
mess with it from interrupt. Now, port B has dangling packet_task
which will race w/ whatever will run on port B.
The problem is that we don't always protect polled ports from
interrupts with ata_qc_set_polling() and for non-DMA ATA commands
there's no way to discern if actually an IRQ has occurred (this
sucks), so we end up finishing the other port's command.
This condition occurs quite often if both port A and B are busy. The
most common result is assertion failure in atapi_packet_task
(assert(qc->flags & ATA_QCFLAG_ACTIVE)), but depending on timing and
on SMP, weirder things could happen, I think.
Note that for ATAPI_DMA, interrupt from the other port won't mess
with a polled command as we can tell that it's not ours with
bmdma_status, but, if spurious interrupt occurs on the port, the
packet_task will go dangling. That's why ATAPI_DMA also needs
protection. The baseline is that all polled qc's need to be protected
with ata_qc_set_polling() until polling task is done with the command.
[ Start of patch descriptions ]
While this is something to look into, the supplied patches are
definitely not the way we want to go. We need to follow the state
diagram for the PACKET command protocol. ATA4 [1] diagrams are a
good thing to read, since they include mention of the behavior of
certain ATAPI devices that can send an interrupt between taskfile-out
and write-cdb steps in the sequence.
In patch #2, you're making ata_irq_on() way too heavy. In patch #1,
calling ata_qc_set_polling() for non-polled commands is a hack.
Have you received patches in the reverse order? #1 changes
ata_irq_on() and #2 adds ata_qc_set_polling().
Hmmm, only a call to ata_chk_status() is added to ata_irq_on(), which
I think is needed regardless of other changes, and ata_wait_idle() is
removed. Does that make the function heavy?
The better solution is to track the PACKET command protocol state
much more closely, so that the code _knows_ when it should and
shouldn't be getting an interrupt.
This is required anyway because, as mentioned in another email, an
ATA device might assert INTRQ for certain events, such as non-data
commands, where the controller is not required to assert the BMDMA
IRQ bit.
I _suspect_ that many host controllers cause the BMDMA IRQ bit to
track the ATA INTRQ status precisely, but this theory has not been
validated.
Jeff
[1] http://www.t13.org/project/d1153r18-ATA-ATAPI-4.pdf
Without interrupt pending information from BMDMA bit for non-DMA
commands (which I don't think we can use for non-DMA cmds as we'll
never be sure if all controllers behave that way), the problem is that
for many SATA controllers, more than one ports share single interrupt
line. And without interrupt pending bit, shared interrupt means a
lot of spurious interrupts making it impossible to know when to expect
interrupts.
Incorrect... this is why I keep harping on the "ATA host state machine."
You rely on proper implementation to know when to expect interrupts.
Read the state diagrams, they tell you precisely when an interrupt may
be expected. By definition, any other interrupt is probably a PCI
shared interrupt, or a hardware or software bug.
I think I'm familiar with ATA host state machine. I don't think I'm
currently saying things because I don't know about it. Maybe I'm
missing something here. Please consider the following scenario.
1. non-DMA command issued.
2. device does something
3. another device sharing the IRQ line raises interrupt
4. D2H FIS received (BSY off, DRDY on, INTR on)
5. interrupt handler kicks in for #3
6. SATA controller raises interrupt
7. SATA handler invoked from #5 checks ATA_STATUS and determines that
completes the command (we don't know if it's our interrupt or not)
8. interrupt handler from #5 returns.
9. interrupt handler for #6.
10. nobody cared.
Did I miss something?
IDE driver deals with this by having only one command active per
interrupt, but SATA doesn't have such scheme yet. And I don't know if
such a scheme is desirable at all. Maybe just continuing to poll
non-DMA commands (which isn't much a burden anyway) and keeping DMA
commands fast is a better approach.
The IDE driver has a high density, but look closely... it follows the
ATA host state machine as well.
Yes it does, and it does a lot of exclusion among ports to do so...
So, how should we do here? To follow ATA/ATAPI state machine, we
need to implement exclusion among ports sharing an interrupt. Is this
the way to go? Arggggggg... Lack of interrupt pending bit is such a
pain in the ass. :-(
If the code knows what state its in, it knows whether or not to expect
an interrupt. All that state information should already be synchronized
by spinlock(host-lock), too.
I think the problem is whether or not we're expecting interrupts,
we'll get interrupts that are't ours and we have no way to tell if
they're ours or not. No?
Thanks.
--
tejun
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html