Checkpatch outputs some warnings about incorrect comment style,
which is fixed by this patch.
Signed-off-by: Anton Würfel <anton.wuer...@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raff...@fau.de>
CC: linux-ker...@i4.cs.fau.de
---
drivers/tty/serial/8250/8250_ingenic.c | 6 ++-
drivers/tty/serial/8250/8250_pnp.c | 6 ++-
drivers/tty/serial/8250/8250_port.c | 29 ++++++-----
drivers/tty/serial/8250/serial_cs.c | 92 +++++++++++++++++++---------------
4 files changed, 75 insertions(+), 58 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_ingenic.c
b/drivers/tty/serial/8250/8250_ingenic.c
index 49394b4..c53d2501 100644
--- a/drivers/tty/serial/8250/8250_ingenic.c
+++ b/drivers/tty/serial/8250/8250_ingenic.c
@@ -153,13 +153,15 @@ static void ingenic_uart_serial_out(struct uart_port *p,
int offset, int value)
case UART_IER:
/* Enable receive timeout interrupt with the
- * receive line status interrupt */
+ * receive line status interrupt
+ */
value |= (value & 0x4) << 2;
break;
case UART_MCR:
/* If we have enabled modem status IRQs we should enable modem
- * mode. */
+ * mode.
+ */
ier = p->serial_in(p, UART_IER);
if (ier & UART_IER_MSI)
diff --git a/drivers/tty/serial/8250/8250_pnp.c
b/drivers/tty/serial/8250/8250_pnp.c
index 1f18065..2731031 100644
--- a/drivers/tty/serial/8250/8250_pnp.c
+++ b/drivers/tty/serial/8250/8250_pnp.c
@@ -367,8 +367,10 @@ static const struct pnp_device_id pnp_dev_table[] = {
{ "PNPCXXX", UNKNOWN_DEV },
/* More unknown PnP modems */
{ "PNPDXXX", UNKNOWN_DEV },
- /* Winbond CIR port, should not be probed. We should keep track
- of it to prevent the legacy serial driver from probing it */
+ /*
+ * Winbond CIR port, should not be probed. We should keep track
+ * of it to prevent the legacy serial driver from probing it
+ */
{ "WEC1022", CIR_PORT },
/*
* SMSC IrCC SIR/FIR port, should not be probed by serial driver
diff --git a/drivers/tty/serial/8250/8250_port.c
b/drivers/tty/serial/8250/8250_port.c
index 57ad0f2..0ec823e 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -250,9 +250,11 @@ static const struct serial8250_config uart_config[] = {
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_AFE,
},
-/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement
-workaround of errata A-008006 which states that tx_loadsz should be
-configured less than Maximum supported fifo bytes */
+ /*
+ * tx_loadsz is set to 63-bytes instead of 64-bytes to implement
+ * workaround of errata A-008006 which states that tx_loadsz should be
+ * configured less than Maximum supported fifo bytes
+ */
[PORT_16550A_FSL64] = {
.name = "16550A_FSL64",
.fifo_size = 64,
@@ -1970,16 +1972,17 @@ int serial8250_do_startup(struct uart_port *port)
serial8250_set_mctrl(port, port->mctrl);
- /* Serial over Lan (SoL) hack:
- Intel 8257x Gigabit ethernet chips have a
- 16550 emulation, to be used for Serial Over Lan.
- Those chips take a longer time than a normal
- serial device to signalize that a transmission
- data was queued. Due to that, the above test generally
- fails. One solution would be to delay the reading of
- iir. However, this is not reliable, since the timeout
- is variable. So, let's just don't test if we receive
- TX irq. This way, we'll never enable UART_BUG_TXEN.
+ /*
+ * Serial over Lan (SoL) hack:
+ * Intel 8257x Gigabit ethernet chips have a
+ * 16550 emulation, to be used for Serial Over Lan.
+ * Those chips take a longer time than a normal
+ * serial device to signalize that a transmission
+ * data was queued. Due to that, the above test generally
+ * fails. One solution would be to delay the reading of
+ * iir. However, this is not reliable, since the timeout
+ * is variable. So, let's just don't test if we receive
+ * TX irq. This way, we'll never enable UART_BUG_TXEN.
*/
if (up->port.flags & UPF_NO_TXEN_TEST)
goto dont_test_tx_en;
diff --git a/drivers/tty/serial/8250/serial_cs.c
b/drivers/tty/serial/8250/serial_cs.c
index f5270ba..a4bdcf6 100644
--- a/drivers/tty/serial/8250/serial_cs.c
+++ b/drivers/tty/serial/8250/serial_cs.c
@@ -1,35 +1,37 @@
-/*======================================================================
-
- A driver for PCMCIA serial devices
-
- serial_cs.c 1.134 2002/05/04 05:48:53
-
- The contents of this file are subject to the Mozilla Public
- License Version 1.1 (the "License"); you may not use this file
- except in compliance with the License. You may obtain a copy of
- the License at http://www.mozilla.org/MPL/
-
- Software distributed under the License is distributed on an "AS
- IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
- implied. See the License for the specific language governing
- rights and limitations under the License.
-
- The initial developer of the original code is David A. Hinds
- <dahi...@users.sourceforge.net>. Portions created by David A. Hinds
- are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
-
- Alternatively, the contents of this file may be used under the
- terms of the GNU General Public License version 2 (the "GPL"), in which
- case the provisions of the GPL are applicable instead of the
- above. If you wish to allow the use of your version of this file
- only under the terms of the GPL and not to allow others to use
- your version of this file under the MPL, indicate your decision
- by deleting the provisions above and replace them with the notice
- and other provisions required by the GPL. If you do not delete
- the provisions above, a recipient may use your version of this
- file under either the MPL or the GPL.
-
-======================================================================*/
+/*
+ * ======================================================================
+ *
+ * A driver for PCMCIA serial devices
+ *
+ * serial_cs.c 1.134 2002/05/04 05:48:53
+ *
+ * The contents of this file are subject to the Mozilla Public
+ * License Version 1.1 (the "License"); you may not use this file
+ * except in compliance with the License. You may obtain a copy of
+ * the License at http://www.mozilla.org/MPL/
+ *
+ * Software distributed under the License is distributed on an "AS
+ * IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
+ * implied. See the License for the specific language governing
+ * rights and limitations under the License.
+ *
+ * The initial developer of the original code is David A. Hinds
+ * <dahi...@users.sourceforge.net>. Portions created by David A. Hinds
+ * are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
+ *
+ * Alternatively, the contents of this file may be used under the
+ * terms of the GNU General Public License version 2 (the "GPL"), in which
+ * case the provisions of the GPL are applicable instead of the
+ * above. If you wish to allow the use of your version of this file
+ * only under the terms of the GPL and not to allow others to use
+ * your version of this file under the MPL, indicate your decision
+ * by deleting the provisions above and replace them with the notice
+ * and other provisions required by the GPL. If you do not delete
+ * the provisions above, a recipient may use your version of this
+ * file under either the MPL or the GPL.
+ *
+ * ======================================================================
+ */
#include <linux/module.h>
#include <linux/moduleparam.h>
@@ -441,16 +443,20 @@ static int simple_config(struct pcmcia_device *link)
struct serial_info *info = link->priv;
int i = -ENODEV, try;
- /* First pass: look for a config entry that looks normal.
- * Two tries: without IO aliases, then with aliases */
+ /*
+ * First pass: look for a config entry that looks normal.
+ * Two tries: without IO aliases, then with aliases
+ */
link->config_flags |= CONF_AUTO_SET_VPP;
for (try = 0; try < 4; try++)
if (!pcmcia_loop_config(link, simple_config_check, &try))
goto found_port;
- /* Second pass: try to find an entry that isn't picky about
- its base address, then try to grab any standard serial port
- address, and finally try to get any free port. */
+ /*
+ * Second pass: try to find an entry that isn't picky about
+ * its base address, then try to grab any standard serial port
+ * address, and finally try to get any free port.
+ */
if (!pcmcia_loop_config(link, simple_config_check_notpicky, NULL))
goto found_port;
@@ -480,8 +486,10 @@ static int multi_config_check(struct pcmcia_device *p_dev,
void *priv_data)
if (p_dev->resource[1]->end)
return -EINVAL;
- /* The quad port cards have bad CIS's, so just look for a
- window larger than 8 ports and assume it will be right */
+ /*
+ * The quad port cards have bad CIS's, so just look for a
+ * window larger than 8 ports and assume it will be right
+ */
if (p_dev->resource[0]->end <= 8)
return -EINVAL;
@@ -623,8 +631,10 @@ static int serial_config(struct pcmcia_device *link)
break;
}
- /* Another check for dual-serial cards: look for either serial or
- multifunction cards that ask for appropriate IO port ranges */
+ /*
+ * Another check for dual-serial cards: look for either serial or
+ * multifunction cards that ask for appropriate IO port ranges
+ */
if ((info->multi == 0) &&
(link->has_func_id) &&
(link->socket->pcmcia_pfc == 0) &&
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
