PMIC pm8150b is a slave pmic and this adds base DTS file for pm8150b with pon, adc, and gpio nodes
Signed-off-by: Vinod Koul <vk...@kernel.org> --- arch/arm64/boot/dts/qcom/pm8150b.dtsi | 84 +++++++++++++++++++++++++++ 1 file changed, 84 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pm8150b.dtsi diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi new file mode 100644 index 000000000000..dfb71fb8c90a --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi @@ -0,0 +1,84 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +#include <dt-bindings/iio/qcom,spmi-vadc.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + pmic@2 { + compatible = "qcom,pm8150b", "qcom,spmi-pmic"; + reg = <0x2 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + + status = "disabled"; + }; + + adc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + status = "disabled"; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + die-temp@6 { + reg = <ADC5_DIE_TEMP>; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + + chg-temp@9 { + reg = <ADC5_CHG_TEMP>; + qcom,pre-scaling = <1 1>; + label = "chg_temp"; + }; + }; + + pm8150b_gpios: gpio@c000 { + compatible = "qcom,pm8150b-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <0x2 0xc0 0 IRQ_TYPE_NONE>, + <0x2 0xc1 0 IRQ_TYPE_NONE>, + <0x2 0xc2 0 IRQ_TYPE_NONE>, + <0x2 0xc3 0 IRQ_TYPE_NONE>, + <0x2 0xc4 0 IRQ_TYPE_NONE>, + <0x2 0xc5 0 IRQ_TYPE_NONE>, + <0x2 0xc6 0 IRQ_TYPE_NONE>, + <0x2 0xc7 0 IRQ_TYPE_NONE>, + <0x2 0xc8 0 IRQ_TYPE_NONE>, + <0x2 0xc9 0 IRQ_TYPE_NONE>, + <0x2 0xca 0 IRQ_TYPE_NONE>, + <0x2 0xcb 0 IRQ_TYPE_NONE>; + }; + }; + + pmic@3 { + compatible = "qcom,pm8150b", "qcom,spmi-pmic"; + reg = <0x3 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +}; -- 2.20.1