On Tue, Aug 20, 2019 at 12:12:11PM +0530, Vinod Koul wrote: > PMIC pm8150b is a slave pmic and this adds base DTS file for pm8150b > with pon, adc, and gpio nodes
All of your other commit messages refers to it as power-on instead of pon, be consistent. > > Signed-off-by: Vinod Koul <[email protected]> > --- > arch/arm64/boot/dts/qcom/pm8150b.dtsi | 84 +++++++++++++++++++++++++++ > 1 file changed, 84 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/pm8150b.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi > b/arch/arm64/boot/dts/qcom/pm8150b.dtsi > new file mode 100644 > index 000000000000..dfb71fb8c90a > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi > @@ -0,0 +1,84 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. > +// Copyright (c) 2019, Linaro Limited > + > +#include <dt-bindings/iio/qcom,spmi-vadc.h> > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/spmi/spmi.h> > + > +&spmi_bus { > + pmic@2 { > + compatible = "qcom,pm8150b", "qcom,spmi-pmic"; > + reg = <0x2 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + power-on@800 { > + compatible = "qcom,pm8916-pon"; > + reg = <0x0800>; > + > + status = "disabled"; > + }; > + > + adc@3100 { > + compatible = "qcom,spmi-adc5"; > + reg = <0x3100>; > + #address-cells = <1>; > + #size-cells = <0>; > + #io-channel-cells = <1>; > + interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; > + > + status = "disabled"; > + > + ref-gnd@0 { > + reg = <ADC5_REF_GND>; > + qcom,pre-scaling = <1 1>; > + label = "ref_gnd"; > + }; > + > + vref-1p25@1 { > + reg = <ADC5_1P25VREF>; > + qcom,pre-scaling = <1 1>; > + label = "vref_1p25"; > + }; > + > + die-temp@6 { > + reg = <ADC5_DIE_TEMP>; > + qcom,pre-scaling = <1 1>; > + label = "die_temp"; > + }; > + > + chg-temp@9 { > + reg = <ADC5_CHG_TEMP>; > + qcom,pre-scaling = <1 1>; > + label = "chg_temp"; > + }; > + }; > + > + pm8150b_gpios: gpio@c000 { > + compatible = "qcom,pm8150b-gpio"; > + reg = <0xc000>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupts = <0x2 0xc0 0 IRQ_TYPE_NONE>, > + <0x2 0xc1 0 IRQ_TYPE_NONE>, > + <0x2 0xc2 0 IRQ_TYPE_NONE>, > + <0x2 0xc3 0 IRQ_TYPE_NONE>, > + <0x2 0xc4 0 IRQ_TYPE_NONE>, > + <0x2 0xc5 0 IRQ_TYPE_NONE>, > + <0x2 0xc6 0 IRQ_TYPE_NONE>, > + <0x2 0xc7 0 IRQ_TYPE_NONE>, > + <0x2 0xc8 0 IRQ_TYPE_NONE>, > + <0x2 0xc9 0 IRQ_TYPE_NONE>, > + <0x2 0xca 0 IRQ_TYPE_NONE>, > + <0x2 0xcb 0 IRQ_TYPE_NONE>; > + }; > + }; > + > + pmic@3 { > + compatible = "qcom,pm8150b", "qcom,spmi-pmic"; > + reg = <0x3 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > +}; > -- > 2.20.1 >
