This change converts all bit flags for the 'struct spi_device' mode to the BIT() macro. The change is mostly for readability. Since adding more bit fields, might as well convert it now.
Signed-off-by: Alexandru Ardelean <[email protected]> --- Changelog v1 -> v2: * https://lore.kernel.org/linux-spi/[email protected]/ * add patch 'spi: convert to BIT() all spi_device flags' * for patch 'spi: Add SPI_NO_TX/RX support' convert comment to new multi-line format * add patch 'spi: dt-bindings: document zero value for spi-{rx,tx}-bus-width properties' include/linux/spi/spi.h | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-) diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index aa09fdc8042d..66c7d8e45563 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -165,27 +165,27 @@ struct spi_device { u8 bits_per_word; bool rt; u32 mode; -#define SPI_CPHA 0x01 /* clock phase */ -#define SPI_CPOL 0x02 /* clock polarity */ +#define SPI_CPHA BIT(0) /* clock phase */ +#define SPI_CPOL BIT(1) /* clock polarity */ #define SPI_MODE_0 (0|0) /* (original MicroWire) */ #define SPI_MODE_1 (0|SPI_CPHA) #define SPI_MODE_2 (SPI_CPOL|0) #define SPI_MODE_3 (SPI_CPOL|SPI_CPHA) #define SPI_MODE_X_MASK (SPI_CPOL|SPI_CPHA) -#define SPI_CS_HIGH 0x04 /* chipselect active high? */ -#define SPI_LSB_FIRST 0x08 /* per-word bits-on-wire */ -#define SPI_3WIRE 0x10 /* SI/SO signals shared */ -#define SPI_LOOP 0x20 /* loopback mode */ -#define SPI_NO_CS 0x40 /* 1 dev/bus, no chipselect */ -#define SPI_READY 0x80 /* slave pulls low to pause */ -#define SPI_TX_DUAL 0x100 /* transmit with 2 wires */ -#define SPI_TX_QUAD 0x200 /* transmit with 4 wires */ -#define SPI_RX_DUAL 0x400 /* receive with 2 wires */ -#define SPI_RX_QUAD 0x800 /* receive with 4 wires */ -#define SPI_CS_WORD 0x1000 /* toggle cs after each word */ -#define SPI_TX_OCTAL 0x2000 /* transmit with 8 wires */ -#define SPI_RX_OCTAL 0x4000 /* receive with 8 wires */ -#define SPI_3WIRE_HIZ 0x8000 /* high impedance turnaround */ +#define SPI_CS_HIGH BIT(2) /* chipselect active high? */ +#define SPI_LSB_FIRST BIT(3) /* per-word bits-on-wire */ +#define SPI_3WIRE BIT(4) /* SI/SO signals shared */ +#define SPI_LOOP BIT(5) /* loopback mode */ +#define SPI_NO_CS BIT(6) /* 1 dev/bus, no chipselect */ +#define SPI_READY BIT(7) /* slave pulls low to pause */ +#define SPI_TX_DUAL BIT(8) /* transmit with 2 wires */ +#define SPI_TX_QUAD BIT(9) /* transmit with 4 wires */ +#define SPI_RX_DUAL BIT(10) /* receive with 2 wires */ +#define SPI_RX_QUAD BIT(11) /* receive with 4 wires */ +#define SPI_CS_WORD BIT(12) /* toggle cs after each word */ +#define SPI_TX_OCTAL BIT(13) /* transmit with 8 wires */ +#define SPI_RX_OCTAL BIT(14) /* receive with 8 wires */ +#define SPI_3WIRE_HIZ BIT(15) /* high impedance turnaround */ int irq; void *controller_state; void *controller_data; -- 2.17.1
