From: Dragos Bogdan <dragos.bog...@analog.com> Transmit/receive only is a valid SPI mode. For example, the MOSI/TX line might be missing from an ADC while for a DAC the MISO/RX line may be optional. This patch adds these two new modes: SPI_NO_TX and SPI_NO_RX. This way, the drivers will be able to identify if any of these two lines is missing and to adjust the transfers accordingly.
Signed-off-by: Dragos Bogdan <dragos.bog...@analog.com> Signed-off-by: Alexandru Ardelean <alexandru.ardel...@analog.com> --- Changelog v1 -> v2: * https://lore.kernel.org/linux-spi/20201111141529.98147-1-alexandru.ardel...@analog.com/ * convert comment to new multi-line format drivers/spi/spi.c | 26 +++++++++++++++++++++----- include/linux/spi/spi.h | 2 ++ 2 files changed, 23 insertions(+), 5 deletions(-) diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index 0c3f3a962448..5784fa8d9d74 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -1939,6 +1939,9 @@ static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi, /* Device DUAL/QUAD mode */ if (!of_property_read_u32(nc, "spi-tx-bus-width", &value)) { switch (value) { + case 0: + spi->mode |= SPI_NO_TX; + break; case 1: break; case 2: @@ -1960,6 +1963,9 @@ static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi, if (!of_property_read_u32(nc, "spi-rx-bus-width", &value)) { switch (value) { + case 0: + spi->mode |= SPI_NO_RX; + break; case 1: break; case 2: @@ -3327,12 +3333,17 @@ int spi_setup(struct spi_device *spi) unsigned bad_bits, ugly_bits; int status; - /* check mode to prevent that DUAL and QUAD set at the same time + /* + * check mode to prevent that any two of DUAL, QUAD and NO_MOSI/MISO + * are set at the same time */ - if (((spi->mode & SPI_TX_DUAL) && (spi->mode & SPI_TX_QUAD)) || - ((spi->mode & SPI_RX_DUAL) && (spi->mode & SPI_RX_QUAD))) { + if ((hweight_long(spi->mode & + (SPI_TX_DUAL | SPI_TX_QUAD | SPI_NO_TX)) > 1) || + (hweight_long(spi->mode & + (SPI_RX_DUAL | SPI_RX_QUAD | SPI_NO_RX)) > 1)) { dev_err(&spi->dev, - "setup: can not select dual and quad at the same time\n"); + "setup: can not select any two of dual, quad and no-rx/tx " + "at the same time\n"); return -EINVAL; } /* if it is SPI_3WIRE mode, DUAL and QUAD should be forbidden @@ -3346,7 +3357,8 @@ int spi_setup(struct spi_device *spi) * SPI_CS_WORD has a fallback software implementation, * so it is ignored here. */ - bad_bits = spi->mode & ~(spi->controller->mode_bits | SPI_CS_WORD); + bad_bits = spi->mode & ~(spi->controller->mode_bits | SPI_CS_WORD | + SPI_NO_TX | SPI_NO_RX); /* nothing prevents from working with active-high CS in case if it * is driven by GPIO. */ @@ -3607,6 +3619,8 @@ static int __spi_validate(struct spi_device *spi, struct spi_message *message) * 2. check tx/rx_nbits match the mode in spi_device */ if (xfer->tx_buf) { + if (spi->mode & SPI_NO_TX) + return -EINVAL; if (xfer->tx_nbits != SPI_NBITS_SINGLE && xfer->tx_nbits != SPI_NBITS_DUAL && xfer->tx_nbits != SPI_NBITS_QUAD) @@ -3620,6 +3634,8 @@ static int __spi_validate(struct spi_device *spi, struct spi_message *message) } /* check transfer rx_nbits */ if (xfer->rx_buf) { + if (spi->mode & SPI_NO_RX) + return -EINVAL; if (xfer->rx_nbits != SPI_NBITS_SINGLE && xfer->rx_nbits != SPI_NBITS_DUAL && xfer->rx_nbits != SPI_NBITS_QUAD) diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index 66c7d8e45563..8f3343d3ac27 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -186,6 +186,8 @@ struct spi_device { #define SPI_TX_OCTAL BIT(13) /* transmit with 8 wires */ #define SPI_RX_OCTAL BIT(14) /* receive with 8 wires */ #define SPI_3WIRE_HIZ BIT(15) /* high impedance turnaround */ +#define SPI_NO_TX BIT(16) /* no transmit wire */ +#define SPI_NO_RX BIT(17) /* no receive wire */ int irq; void *controller_state; void *controller_data; -- 2.17.1
