On Mon, Jan 15, 2001 at 08:49:56PM -0800, Linus Torvalds wrote:
> So what I _think_ is the correct change is to do roughly this in
> arch/i386/kernel/pci-irq.c:
>
> - in pcibios_fixup_irqs(), remove the
>
> #idef CONFIG_X86_IO_APIC
> ...
> #endif
>
> section entirely.
>
> - in pcibios_enable_irq(), at the _end_ (after having enabled the irq
> with "pcibios_lookup_irq(dev, 1)", do something like
>
> irq = IO_APIC_get_PCI_irq_vector(dev->bus->number, PCI_SLOT(dev->devfn), pin);
> if (irq > 0)
> dev->irq = irq;
>
> and add a LOT of debug printk's, and enable DEBUG in pci-i386.h.
I did the changes above to 2.4.0 source.
Kernel with these changes can't detect my SCSI drive. It prints these messages
in cycle:
SCSI host 0 abort (pid 0) timed out - resetting
SCSI host is being reset for host 0 channel 0
SCSI host 0 channel 0 reset (pid 0) timed out - trying harder
SCSI host is being reset for host 0 channel 0
Same configuration without changes above detects SCSI drive without problem.
For completness, made changes are attached.
Could anybody help?
Petr
---------------------------------------------------------------
Petr Matula [EMAIL PROTECTED]
http://www.fi.muni.cz/~pem
---------------------------------------------------------------
--- linux/arch/i386/kernel/pci-irq.c Thu Jan 4 05:45:26 2001
+++ linux~/arch/i386/kernel/pci-irq.c Wed Jan 17 17:30:53 2001
@@ -559,40 +559,6 @@
pci_for_each_dev(dev) {
pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
-#ifdef CONFIG_X86_IO_APIC
- /*
- * Recalculate IRQ numbers if we use the I/O APIC.
- */
- if (io_apic_assign_pci_irqs)
- {
- int irq;
-
- if (pin) {
- pin--; /* interrupt pins are numbered
starting from 1 */
- irq = IO_APIC_get_PCI_irq_vector(dev->bus->number,
PCI_SLOT(dev->devfn), pin);
-/*
- * Will be removed completely if things work out well with fuzzy parsing
- */
-#if 0
- if (irq < 0 && dev->bus->parent) { /* go back to the
bridge */
- struct pci_dev * bridge = dev->bus->self;
-
- pin = (pin + PCI_SLOT(dev->devfn)) % 4;
- irq =
IO_APIC_get_PCI_irq_vector(bridge->bus->number,
- PCI_SLOT(bridge->devfn), pin);
- if (irq >= 0)
- printk(KERN_WARNING "PCI: using
PPB(B%d,I%d,P%d) to get irq %d\n",
- bridge->bus->number,
PCI_SLOT(bridge->devfn), pin, irq);
- }
-#endif
- if (irq >= 0) {
- printk("PCI->APIC IRQ transform: (B%d,I%d,P%d)
-> %d\n",
- dev->bus->number,
PCI_SLOT(dev->devfn), pin, irq);
- dev->irq = irq;
- }
- }
- }
-#endif
/*
* Still no IRQ? Try to lookup one...
*/
@@ -612,6 +578,7 @@
void pcibios_enable_irq(struct pci_dev *dev)
{
+ unsigned int irq;
u8 pin;
pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
if (pin && !pcibios_lookup_irq(dev, 1) && !dev->irq) {
@@ -624,5 +591,14 @@
msg = " Please try using pci=biosirq.";
printk(KERN_WARNING "PCI: No IRQ known for interrupt pin %c of device
%s.%s\n",
'A' + pin - 1, dev->slot_name, msg);
+
+ printk("Doing: IO_APIC_get_PCI_irq_vector\n");
+ printk("dev->bus->number : %c\n",dev->bus->number);
+ printk("PCI_SLOT(dev->devfn): %d\n",PCI_SLOT(dev->devfn));
+ printk("pin : %hhd\n",pin);
+ irq = IO_APIC_get_PCI_irq_vector(dev->bus->number,
+PCI_SLOT(dev->devfn), pin);
+ printk("assigned irq : %u\n",irq);
+ if (irq > 0)
+ dev->irq = irq;
}
}
