On Thu, 10 Jan 2013, Roger Quadros wrote:
> If the OMAP's Host controller is in PHY mode then we instantiate
> a platform device for the PHY (one for each port in PHY mode) and
> hold a reference to it so that we can use the usb_phy API, e.g.
> while suspend/resume.
>
> The platform data for the PHY must be supplied in the newly added
> .phy_config parameter in struct usbhs_omap_platform_data.
>
> The end goal is to move the PHY's reset and power handling code
> out of the ehci-omap driver and into the phy driver.
As mentioned in another thread, I would prefer to have these changes to
ehci-omap.c made after the driver is converted to the new "ehci-hcd is
a library" scheme. The patch below does the conversion; it is meant to
apply on top of the similar patch for ehci-mxc posted recently on the
linux-usb mailing list.
After this conversion, the omap_ehci_hcd private data structure doesn't
have to be allocated specifically. It can be handled in the same way
as the private data structure in the ehci-mxc patch.
I haven't even tried to compile this. Please let me know how it works.
Alan Stern
Index: usb-3.7/drivers/usb/host/Kconfig
===================================================================
--- usb-3.7.orig/drivers/usb/host/Kconfig
+++ usb-3.7/drivers/usb/host/Kconfig
@@ -155,7 +155,7 @@ config USB_EHCI_MXC
Variation of ARC USB block used in some Freescale chips.
config USB_EHCI_HCD_OMAP
- bool "EHCI support for OMAP3 and later chips"
+ tristate "EHCI support for OMAP3 and later chips"
depends on USB_EHCI_HCD && ARCH_OMAP
default y
---help---
Index: usb-3.7/drivers/usb/host/Makefile
===================================================================
--- usb-3.7.orig/drivers/usb/host/Makefile
+++ usb-3.7/drivers/usb/host/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
obj-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o
obj-$(CONFIG_USB_EHCI_HCD_PLATFORM) += ehci-platform.o
obj-$(CONFIG_USB_EHCI_MXC) += ehci-mxc.o
+obj-$(CONFIG_USB_EHCI_HCD_OMAP) += ehci-omap.o
obj-$(CONFIG_USB_OXU210HP_HCD) += oxu210hp-hcd.o
obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
Index: usb-3.7/drivers/usb/host/ehci-hcd.c
===================================================================
--- usb-3.7.orig/drivers/usb/host/ehci-hcd.c
+++ usb-3.7/drivers/usb/host/ehci-hcd.c
@@ -1255,11 +1255,6 @@ MODULE_LICENSE ("GPL");
#define PLATFORM_DRIVER ehci_hcd_sh_driver
#endif
-#ifdef CONFIG_USB_EHCI_HCD_OMAP
-#include "ehci-omap.c"
-#define PLATFORM_DRIVER ehci_hcd_omap_driver
-#endif
-
#ifdef CONFIG_PPC_PS3
#include "ehci-ps3.c"
#define PS3_SYSTEM_BUS_DRIVER ps3_ehci_driver
@@ -1349,6 +1344,7 @@ MODULE_LICENSE ("GPL");
!IS_ENABLED(CONFIG_USB_EHCI_HCD_PLATFORM) && \
!defined(CONFIG_USB_CHIPIDEA_HOST) && \
!defined(CONFIG_USB_EHCI_MXC) && \
+ !defined(CONFIG_USB_EHCI_HCD_OMAP) && \
!defined(PLATFORM_DRIVER) && \
!defined(PS3_SYSTEM_BUS_DRIVER) && \
!defined(OF_PLATFORM_DRIVER) && \
Index: usb-3.7/drivers/usb/host/ehci-omap.c
===================================================================
--- usb-3.7.orig/drivers/usb/host/ehci-omap.c
+++ usb-3.7/drivers/usb/host/ehci-omap.c
@@ -36,6 +36,9 @@
* - convert to use hwmod and runtime PM
*/
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/io.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/usb/ulpi.h>
@@ -44,6 +47,10 @@
#include <linux/pm_runtime.h>
#include <linux/gpio.h>
#include <linux/clk.h>
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
+
+#include "ehci.h"
/* EHCI Register Set */
#define EHCI_INSNREG04 (0xA0)
@@ -56,11 +63,13 @@
#define EHCI_INSNREG05_ULPI_EXTREGADD_SHIFT 8
#define EHCI_INSNREG05_ULPI_WRDATA_SHIFT 0
-/*-------------------------------------------------------------------------*/
+#define DRIVER_DESC = "OMAP-EHCI Host Controller driver";
-static const struct hc_driver ehci_omap_hc_driver;
+static const char hcd_name[] = "ehci-omap";
+/*-------------------------------------------------------------------------*/
+
static inline void ehci_write(void __iomem *base, u32 reg, u32 val)
{
__raw_writel(val, base + reg);
@@ -165,6 +174,12 @@ static void disable_put_regulator(
/* configure so an HC device and id are always provided */
/* always called with process context; sleeping is OK */
+static struct hc_driver __read_mostly ehci_omap_hc_driver;
+
+static const struct ehci_driver_overrides ehci_omap_overrides __initdata = {
+ .reset = omap_ehci_init,
+};
+
/**
* ehci_hcd_omap_probe - initialize TI-based HCDs
*
@@ -322,56 +337,33 @@ static struct platform_driver ehci_hcd_o
/*.suspend = ehci_hcd_omap_suspend, */
/*.resume = ehci_hcd_omap_resume, */
.driver = {
- .name = "ehci-omap",
+ .name = hcd_name,
}
};
/*-------------------------------------------------------------------------*/
-static const struct hc_driver ehci_omap_hc_driver = {
- .description = hcd_name,
- .product_desc = "OMAP-EHCI Host Controller",
- .hcd_priv_size = sizeof(struct ehci_hcd),
-
- /*
- * generic hardware linkage
- */
- .irq = ehci_irq,
- .flags = HCD_MEMORY | HCD_USB2,
-
- /*
- * basic lifecycle operations
- */
- .reset = omap_ehci_init,
- .start = ehci_run,
- .stop = ehci_stop,
- .shutdown = ehci_shutdown,
-
- /*
- * managing i/o requests and associated device resources
- */
- .urb_enqueue = ehci_urb_enqueue,
- .urb_dequeue = ehci_urb_dequeue,
- .endpoint_disable = ehci_endpoint_disable,
- .endpoint_reset = ehci_endpoint_reset,
+static int __init ehci_omap_init(void)
+{
+ if (usb_disabled())
+ return -ENODEV;
- /*
- * scheduling support
- */
- .get_frame_number = ehci_get_frame,
+ pr_info("%s: " DRIVER_DESC "\n", hcd_name);
- /*
- * root hub support
- */
- .hub_status_data = ehci_hub_status_data,
- .hub_control = ehci_hub_control,
- .bus_suspend = ehci_bus_suspend,
- .bus_resume = ehci_bus_resume,
+ ehci_init_driver(&ehci_omap_hc_driver, &ehci_omap_overrides);
+ return platform_driver_register(&ehci_omap_driver);
+}
+module_init(ehci_omap_init);
- .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete,
-};
+static void __exit ehci_omap_cleanup(void)
+{
+ platform_driver_unregister(&ehci_omap_driver);
+}
+module_exit(ehci_omap_cleanup);
MODULE_ALIAS("platform:omap-ehci");
MODULE_AUTHOR("Texas Instruments, Inc.");
MODULE_AUTHOR("Felipe Balbi <felipe.ba...@nokia.com>");
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
