On 01/11/2013 05:28 PM, Alan Stern wrote:
> On Fri, 11 Jan 2013, Roger Quadros wrote:
>
>> Alan,
>>
>> Thanks for the patch. I've pasted the version that builds and works and
>> put you as the Author of the patch, hope it is fine.
>
> As far as I can see, yours is the same as what I posted except that:
>
> You altered the changes to ehci-hcd.c and Makefile to remove
> the dependency on the ehci-mxc patch;
>
> You made an unimportant whitespace change in ehci-omap.c
> (moved a blank line before ehci_write()).
>
> Right? It's hard to compare the patches directly because the one you
> posted was whitespace-damaged.
My bad pasting it. Patch is attached now.
Apart from what you mentioned I did some more trivial changes. e.g.
+ !IS_ENABLED(CONFIG_USB_EHCI_HCD_OMAP) && \
instead of
+ !defined(CONFIG_USB_EHCI_HCD_OMAP) && \
use ehci_hcd_omap_driver instead of ehci_omap_driver
>
> Anyway, if this is okay and there's nothing wrong with the ehci-mxc
> change (other than the comment for ehci->priv), I'll submit both of
> them to Greg soon.
>
OK, thanks.
I tried using ehci->priv in ehci-omap driver but noticed that the
private data gets corrupted after the EHCI controller is running and has
enumerated a few devices.
If I disable USB_DEBUG then things are fine. Could it be possible
that someone is overflowing data when USB_DEBUG is enabled?
My implementation is pasted below. (May contain whitespace errors due to
MS exchange). Patch 2 attached in case.
What was happening there is that omap_priv->phy was not the same during
remove() as it was set to during probe().
Would be nice if you could check if the same happens with ehci-mxc.
cheers,
-roger
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index 6388aa6..23c9b9c 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -70,6 +70,11 @@ static const char hcd_name[] = "ehci-omap";
/*-------------------------------------------------------------------------*/
+struct omap_ehci_hcd {
+ struct usb_hcd *hcd;
+ struct usb_phy **phy; /* one PHY for each port */
+ int nports;
+};
static inline void ehci_write(void __iomem *base, u32 reg, u32 val)
{
@@ -194,6 +199,8 @@ static int ehci_hcd_omap_probe(struct
platform_device *pdev)
struct usbhs_omap_platform_data *pdata = dev->platform_data;
struct resource *res;
struct usb_hcd *hcd;
+ struct omap_ehci_hcd *omap_hcd;
+ struct usb_phy *phy;
void __iomem *regs;
int ret = -ENODEV;
int irq;
@@ -208,6 +215,25 @@ static int ehci_hcd_omap_probe(struct
platform_device *pdev)
return -ENODEV;
}
+ if (!pdata) {
+ dev_err(dev, "Missing platform data\n");
+ return -ENODEV;
+ }
+
+ omap_hcd = devm_kzalloc(&pdev->dev, sizeof(*omap_hcd), GFP_KERNEL);
+ if (!omap_hcd) {
+ dev_err(dev, "Memory allocation failed\n");
+ return -ENOMEM;
+ }
+
+ omap_hcd->nports = pdata->nports;
+ i = sizeof(struct usb_phy *) * omap_hcd->nports;
+ omap_hcd->phy = devm_kzalloc(&pdev->dev, i, GFP_KERNEL);
+ if (!omap_hcd->phy) {
+ dev_err(dev, "Memory allocation failed\n");
+ return -ENOMEM;
+ }
+
irq = platform_get_irq_byname(pdev, "ehci-irq");
if (irq < 0) {
dev_err(dev, "EHCI irq failed\n");
@@ -238,9 +264,15 @@ static int ehci_hcd_omap_probe(struct
platform_device *pdev)
hcd->rsrc_start = res->start;
hcd->rsrc_len = resource_size(res);
hcd->regs = regs;
+ omap_hcd->hcd = hcd;
+
+ platform_set_drvdata(pdev, omap_hcd);
/* get ehci regulator and enable */
- for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
+ for (i = 0 ; i < omap_hcd->nports ; i++) {
+ struct platform_device *phy_pdev;
+ struct usbhs_phy_config *phy_config;
+
if (pdata->port_mode[i] != OMAP_EHCI_PORT_MODE_PHY) {
pdata->regulator[i] = NULL;
continue;
@@ -254,6 +286,33 @@ static int ehci_hcd_omap_probe(struct
platform_device *pdev)
} else {
regulator_enable(pdata->regulator[i]);
}
+
+ /* instantiate PHY */
+ if (!pdata->phy_config[i]) {
+ dev_dbg(dev, "missing phy_config for port %d\n", i);
+ continue;
+ }
+
+ phy_config = pdata->phy_config[i];
+ phy_pdev = platform_device_register_data(&pdev->dev,
+ phy_config->name, i, phy_config->pdata,
+ phy_config->pdata_size);
+ if (IS_ERR(phy_pdev)) {
+ dev_dbg(dev, "error creating PHY device for port %d\n",
+ i);
+ }
+
+ phy = usb_get_phy_from_dev(&phy_pdev->dev);
+ if (IS_ERR(phy)) {
+ dev_dbg(dev, "could not get USB PHY for port %d\n", i);
+ platform_device_unregister(phy_pdev);
+ continue;
+ }
+
+ usb_phy_init(phy);
+ omap_hcd->phy[i] = phy;
+ /* bring PHY out of suspend */
+ usb_phy_set_suspend(omap_hcd->phy[i], 0);
}
pm_runtime_enable(dev);
@@ -284,6 +343,12 @@ err_pm_runtime:
disable_put_regulator(pdata);
pm_runtime_put_sync(dev);
usb_put_hcd(hcd);
+ for (i = 0 ; i < omap_hcd->nports ; i++) {
+ phy = omap_hcd->phy[i];
+ if (!phy)
+ continue;
+ platform_device_unregister(to_platform_device(phy->dev));
+ }
err_io:
iounmap(regs);
@@ -301,14 +366,26 @@ err_io:
*/
static int ehci_hcd_omap_remove(struct platform_device *pdev)
{
- struct device *dev = &pdev->dev;
- struct usb_hcd *hcd = dev_get_drvdata(dev);
+ struct device *dev = &pdev->dev;
+ struct omap_ehci_hcd *omap_hcd = dev_get_drvdata(dev);
+ struct usb_hcd *hcd = omap_hcd->hcd;
+ int i;
usb_remove_hcd(hcd);
disable_put_regulator(dev->platform_data);
iounmap(hcd->regs);
usb_put_hcd(hcd);
+ for (i = 0; i < omap_hcd->nports; i++) {
+ struct usb_phy *phy = omap_hcd->phy[i];
+
+ if (!phy)
+ continue;
+
+ usb_phy_shutdown(phy);
+ platform_device_unregister(to_platform_device(phy->dev));
+ }
+
pm_runtime_put_sync(dev);
pm_runtime_disable(dev);
diff --git a/include/linux/platform_data/usb-omap.h
b/include/linux/platform_data/usb-omap.h
index d63eb7d..927b8a1 100644
--- a/include/linux/platform_data/usb-omap.h
+++ b/include/linux/platform_data/usb-omap.h
@@ -38,6 +38,12 @@ enum usbhs_omap_port_mode {
OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM
};
+struct usbhs_phy_config {
+ char *name; /* binds to device driver */
+ void *pdata; /* platform data for the phy */
+ size_t pdata_size;
+};
+
struct usbhs_omap_platform_data {
int nports;
enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS];
@@ -49,6 +55,8 @@ struct usbhs_omap_platform_data {
unsigned single_ulpi_bypass:1;
unsigned es2_compatibility:1;
unsigned phy_reset:1;
+
+ struct usbhs_phy_config *phy_config[OMAP3_HS_USB_PORTS];
};
/*-------------------------------------------------------------------------*/
--
1.7.4.1
>From fafa9c787bcf2ff3f46c07c045997614d7a8a417 Mon Sep 17 00:00:00 2001
From: Alan Stern <st...@rowland.harvard.edu>
Date: Fri, 11 Jan 2013 12:37:01 +0200
Subject: [PATCH] USB: ehci-omap: Convert to platform driver
Convert ehci-omap into a platform driver and use ehci-hcd
as a library.
CC: Alan Stern <st...@rowland.harvard.edu>
Signed-off-by: Roger Quadros <rog...@ti.com>
---
drivers/usb/host/Kconfig | 2 +-
drivers/usb/host/Makefile | 1 +
drivers/usb/host/ehci-hcd.c | 6 +---
drivers/usb/host/ehci-omap.c | 76 +++++++++++++++++++-----------------------
4 files changed, 37 insertions(+), 48 deletions(-)
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index d6bb128..432a463 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -155,7 +155,7 @@ config USB_EHCI_MXC
Variation of ARC USB block used in some Freescale chips.
config USB_EHCI_HCD_OMAP
- bool "EHCI support for OMAP3 and later chips"
+ tristate "EHCI support for OMAP3 and later chips"
depends on USB_EHCI_HCD && ARCH_OMAP
default y
---help---
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 1eb4c30..8a8d079 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_PCI) += pci-quirks.o
obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
obj-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o
obj-$(CONFIG_USB_EHCI_HCD_PLATFORM) += ehci-platform.o
+obj-$(CONFIG_USB_EHCI_HCD_OMAP) += ehci-omap.o
obj-$(CONFIG_USB_OXU210HP_HCD) += oxu210hp-hcd.o
obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index c97503b..c44ef1d 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -1260,11 +1260,6 @@ MODULE_LICENSE ("GPL");
#define PLATFORM_DRIVER ehci_hcd_sh_driver
#endif
-#ifdef CONFIG_USB_EHCI_HCD_OMAP
-#include "ehci-omap.c"
-#define PLATFORM_DRIVER ehci_hcd_omap_driver
-#endif
-
#ifdef CONFIG_PPC_PS3
#include "ehci-ps3.c"
#define PS3_SYSTEM_BUS_DRIVER ps3_ehci_driver
@@ -1352,6 +1347,7 @@ MODULE_LICENSE ("GPL");
#if !IS_ENABLED(CONFIG_USB_EHCI_PCI) && \
!IS_ENABLED(CONFIG_USB_EHCI_HCD_PLATFORM) && \
+ !IS_ENABLED(CONFIG_USB_EHCI_HCD_OMAP) && \
!defined(CONFIG_USB_CHIPIDEA_HOST) && \
!defined(PLATFORM_DRIVER) && \
!defined(PS3_SYSTEM_BUS_DRIVER) && \
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index b96a4bf..6388aa6 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -36,6 +36,9 @@
* - convert to use hwmod and runtime PM
*/
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/io.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/usb/ulpi.h>
@@ -43,6 +46,10 @@
#include <linux/pm_runtime.h>
#include <linux/gpio.h>
#include <linux/clk.h>
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
+
+#include "ehci.h"
#include <linux/platform_data/usb-omap.h>
@@ -57,9 +64,11 @@
#define EHCI_INSNREG05_ULPI_EXTREGADD_SHIFT 8
#define EHCI_INSNREG05_ULPI_WRDATA_SHIFT 0
-/*-------------------------------------------------------------------------*/
+#define DRIVER_DESC "OMAP-EHCI Host Controller driver"
-static const struct hc_driver ehci_omap_hc_driver;
+static const char hcd_name[] = "ehci-omap";
+
+/*-------------------------------------------------------------------------*/
static inline void ehci_write(void __iomem *base, u32 reg, u32 val)
@@ -166,6 +175,12 @@ static void disable_put_regulator(
/* configure so an HC device and id are always provided */
/* always called with process context; sleeping is OK */
+static struct hc_driver __read_mostly ehci_omap_hc_driver;
+
+static const struct ehci_driver_overrides ehci_omap_overrides __initdata = {
+ .reset = omap_ehci_init,
+};
+
/**
* ehci_hcd_omap_probe - initialize TI-based HCDs
*
@@ -315,56 +330,33 @@ static struct platform_driver ehci_hcd_omap_driver = {
/*.suspend = ehci_hcd_omap_suspend, */
/*.resume = ehci_hcd_omap_resume, */
.driver = {
- .name = "ehci-omap",
+ .name = hcd_name,
}
};
/*-------------------------------------------------------------------------*/
-static const struct hc_driver ehci_omap_hc_driver = {
- .description = hcd_name,
- .product_desc = "OMAP-EHCI Host Controller",
- .hcd_priv_size = sizeof(struct ehci_hcd),
-
- /*
- * generic hardware linkage
- */
- .irq = ehci_irq,
- .flags = HCD_MEMORY | HCD_USB2,
-
- /*
- * basic lifecycle operations
- */
- .reset = omap_ehci_init,
- .start = ehci_run,
- .stop = ehci_stop,
- .shutdown = ehci_shutdown,
-
- /*
- * managing i/o requests and associated device resources
- */
- .urb_enqueue = ehci_urb_enqueue,
- .urb_dequeue = ehci_urb_dequeue,
- .endpoint_disable = ehci_endpoint_disable,
- .endpoint_reset = ehci_endpoint_reset,
+static int __init ehci_omap_init(void)
+{
+ if (usb_disabled())
+ return -ENODEV;
- /*
- * scheduling support
- */
- .get_frame_number = ehci_get_frame,
+ pr_info("%s: " DRIVER_DESC "\n", hcd_name);
- /*
- * root hub support
- */
- .hub_status_data = ehci_hub_status_data,
- .hub_control = ehci_hub_control,
- .bus_suspend = ehci_bus_suspend,
- .bus_resume = ehci_bus_resume,
+ ehci_init_driver(&ehci_omap_hc_driver, &ehci_omap_overrides);
+ return platform_driver_register(&ehci_hcd_omap_driver);
+}
+module_init(ehci_omap_init);
- .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete,
-};
+static void __exit ehci_omap_cleanup(void)
+{
+ platform_driver_unregister(&ehci_hcd_omap_driver);
+}
+module_exit(ehci_omap_cleanup);
MODULE_ALIAS("platform:omap-ehci");
MODULE_AUTHOR("Texas Instruments, Inc.");
MODULE_AUTHOR("Felipe Balbi <felipe.ba...@nokia.com>");
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
--
1.7.4.1
>From 1f0e3fdaeda35c96edfdc551434cc841f3b65363 Mon Sep 17 00:00:00 2001
From: Roger Quadros <rog...@ti.com>
Date: Tue, 8 Jan 2013 16:05:16 +0200
Subject: [PATCH] usb: ehci-omap: Instantiate PHY devices if required
If the OMAP's Host controller is in PHY mode then we instantiate
a platform device for the PHY (one for each port in PHY mode) and
hold a reference to it so that we can use the usb_phy API, e.g.
while suspend/resume.
The platform data for the PHY must be supplied in the newly added
.phy_config parameter in struct usbhs_omap_platform_data.
The end goal is to move the PHY's reset and power handling code
out of the ehci-omap driver and into the phy driver.
Signed-off-by: Roger Quadros <rog...@ti.com>
---
drivers/usb/host/ehci-omap.c | 83 ++++++++++++++++++++++++++++++-
include/linux/platform_data/usb-omap.h | 8 +++
2 files changed, 88 insertions(+), 3 deletions(-)
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index 6388aa6..23c9b9c 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -70,6 +70,11 @@ static const char hcd_name[] = "ehci-omap";
/*-------------------------------------------------------------------------*/
+struct omap_ehci_hcd {
+ struct usb_hcd *hcd;
+ struct usb_phy **phy; /* one PHY for each port */
+ int nports;
+};
static inline void ehci_write(void __iomem *base, u32 reg, u32 val)
{
@@ -194,6 +199,8 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
struct usbhs_omap_platform_data *pdata = dev->platform_data;
struct resource *res;
struct usb_hcd *hcd;
+ struct omap_ehci_hcd *omap_hcd;
+ struct usb_phy *phy;
void __iomem *regs;
int ret = -ENODEV;
int irq;
@@ -208,6 +215,25 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
return -ENODEV;
}
+ if (!pdata) {
+ dev_err(dev, "Missing platform data\n");
+ return -ENODEV;
+ }
+
+ omap_hcd = devm_kzalloc(&pdev->dev, sizeof(*omap_hcd), GFP_KERNEL);
+ if (!omap_hcd) {
+ dev_err(dev, "Memory allocation failed\n");
+ return -ENOMEM;
+ }
+
+ omap_hcd->nports = pdata->nports;
+ i = sizeof(struct usb_phy *) * omap_hcd->nports;
+ omap_hcd->phy = devm_kzalloc(&pdev->dev, i, GFP_KERNEL);
+ if (!omap_hcd->phy) {
+ dev_err(dev, "Memory allocation failed\n");
+ return -ENOMEM;
+ }
+
irq = platform_get_irq_byname(pdev, "ehci-irq");
if (irq < 0) {
dev_err(dev, "EHCI irq failed\n");
@@ -238,9 +264,15 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
hcd->rsrc_start = res->start;
hcd->rsrc_len = resource_size(res);
hcd->regs = regs;
+ omap_hcd->hcd = hcd;
+
+ platform_set_drvdata(pdev, omap_hcd);
/* get ehci regulator and enable */
- for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
+ for (i = 0 ; i < omap_hcd->nports ; i++) {
+ struct platform_device *phy_pdev;
+ struct usbhs_phy_config *phy_config;
+
if (pdata->port_mode[i] != OMAP_EHCI_PORT_MODE_PHY) {
pdata->regulator[i] = NULL;
continue;
@@ -254,6 +286,33 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
} else {
regulator_enable(pdata->regulator[i]);
}
+
+ /* instantiate PHY */
+ if (!pdata->phy_config[i]) {
+ dev_dbg(dev, "missing phy_config for port %d\n", i);
+ continue;
+ }
+
+ phy_config = pdata->phy_config[i];
+ phy_pdev = platform_device_register_data(&pdev->dev,
+ phy_config->name, i, phy_config->pdata,
+ phy_config->pdata_size);
+ if (IS_ERR(phy_pdev)) {
+ dev_dbg(dev, "error creating PHY device for port %d\n",
+ i);
+ }
+
+ phy = usb_get_phy_from_dev(&phy_pdev->dev);
+ if (IS_ERR(phy)) {
+ dev_dbg(dev, "could not get USB PHY for port %d\n", i);
+ platform_device_unregister(phy_pdev);
+ continue;
+ }
+
+ usb_phy_init(phy);
+ omap_hcd->phy[i] = phy;
+ /* bring PHY out of suspend */
+ usb_phy_set_suspend(omap_hcd->phy[i], 0);
}
pm_runtime_enable(dev);
@@ -284,6 +343,12 @@ err_pm_runtime:
disable_put_regulator(pdata);
pm_runtime_put_sync(dev);
usb_put_hcd(hcd);
+ for (i = 0 ; i < omap_hcd->nports ; i++) {
+ phy = omap_hcd->phy[i];
+ if (!phy)
+ continue;
+ platform_device_unregister(to_platform_device(phy->dev));
+ }
err_io:
iounmap(regs);
@@ -301,14 +366,26 @@ err_io:
*/
static int ehci_hcd_omap_remove(struct platform_device *pdev)
{
- struct device *dev = &pdev->dev;
- struct usb_hcd *hcd = dev_get_drvdata(dev);
+ struct device *dev = &pdev->dev;
+ struct omap_ehci_hcd *omap_hcd = dev_get_drvdata(dev);
+ struct usb_hcd *hcd = omap_hcd->hcd;
+ int i;
usb_remove_hcd(hcd);
disable_put_regulator(dev->platform_data);
iounmap(hcd->regs);
usb_put_hcd(hcd);
+ for (i = 0; i < omap_hcd->nports; i++) {
+ struct usb_phy *phy = omap_hcd->phy[i];
+
+ if (!phy)
+ continue;
+
+ usb_phy_shutdown(phy);
+ platform_device_unregister(to_platform_device(phy->dev));
+ }
+
pm_runtime_put_sync(dev);
pm_runtime_disable(dev);
diff --git a/include/linux/platform_data/usb-omap.h b/include/linux/platform_data/usb-omap.h
index d63eb7d..927b8a1 100644
--- a/include/linux/platform_data/usb-omap.h
+++ b/include/linux/platform_data/usb-omap.h
@@ -38,6 +38,12 @@ enum usbhs_omap_port_mode {
OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM
};
+struct usbhs_phy_config {
+ char *name; /* binds to device driver */
+ void *pdata; /* platform data for the phy */
+ size_t pdata_size;
+};
+
struct usbhs_omap_platform_data {
int nports;
enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS];
@@ -49,6 +55,8 @@ struct usbhs_omap_platform_data {
unsigned single_ulpi_bypass:1;
unsigned es2_compatibility:1;
unsigned phy_reset:1;
+
+ struct usbhs_phy_config *phy_config[OMAP3_HS_USB_PORTS];
};
/*-------------------------------------------------------------------------*/
--
1.7.4.1
