>From: [EMAIL PROTECTED]
>Date: Wed, 3 Feb 1999 09:41:04 -0600
>Is the Tape on the MegaRAID card or some other controller? And what type
>of
>tape is it? I wonder if this might be like problems commonly seen on
>Adaptec
>controllers unless we slowdown the max sync transfer rate to the tape.
This is de output of "dmesg" (the must important)
--------------------------------------------
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
...
(scsi0) <Adaptec AIC-7880 Ultra SCSI host adapter> found at PCI 10/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) Downloading sequencer code... 419 instructions downloaded
(scsi1) <Adaptec AIC-7880 Ultra SCSI host adapter> found at PCI 11/0
(scsi1) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi1) Downloading sequencer code... 419 instructions downloaded
megaraid: found 0x101e:0x9010:idx 0:bus 1:slot 1:fun 0
scsi2: Found a MegaRAID controller at 0xec10, IRQ: 15
megaraid: [:] detected 1 logical drives
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.4/3.2.4
<Adaptec AIC-7880 Ultra SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.4/3.2.4
<Adaptec AIC-7880 Ultra SCSI host adapter>
scsi2 : AMI MegaRAID 254 commands 16 targs 1 chans
scsi : 3 hosts.
Vendor: HP Model: 4.26GB B 80-0854 Rev: 0854
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 1, lun 0
Vendor: SONY Model: CD-ROM CDU-415 Rev: 1.1n
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 4, lun 0
Vendor: HP Model: C1533A Rev: A708
Type: Sequential-Access ANSI SCSI revision: 02
Detected scsi tape st0 at scsi0, channel 0, id 5, lun 0
scsi2: scanning channel A for devices.
scsi2: scanning channel B for devices.
Vendor: MegaRAID Model: LD0 RAID5 8132R Rev: A
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi2, channel 1, id 0, lun 0
scsi : detected 1 SCSI tape 1 SCSI cdrom 2 SCSI disks total.
(scsi0:0:1:0) Synchronous at 40.0 Mbyte/sec, offset 8.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 8330543 [4067 MB] [4.1
GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 16654336 [8132 MB] [8.1
GB]
--------------------------------------------------
cheers
Carlos Bote
-----Original Message-----
From: Carlos Bote [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, February 03, 1999 7:06 AM
To: [EMAIL PROTECTED]
Cc: [EMAIL PROTECTED]
Subject: MEGARAID PROBLEM WITH KERNEL 2.2.1 ?
Hello all
I think i've found a problem in the MEGARAID driver for HP NetRaid card.
With Kernel 2.0.36 and his patch works fine, but with kernel 2.2.1, when I
do a complete backup with "tar" or with "dd" (or similar, "amanda",
"taper" , "dump") I get the message (after some archives)
"SCSI: Aborting command due to timeout: pid 53243, SCSI 2, channel 1, id 0
lun 0
Write (8) 00 40 67 04 00"
And the system crash. The system has support for SMP with dual Pentium II.
Can you help me, please, urgent !!
Good Bye
