Did you use persistent superblocks in your raidtab?
Clay
-----Original Message-----
From: Pat Heath [mailto:[EMAIL PROTECTED]]
Sent: Friday, October 08, 1999 9:50 AM
To: [EMAIL PROTECTED]
Subject: Raid0
I was working on doing the autostart for raid0 and the part where it says:
3. The partition-types of the devices used in the RAID must be set to
0xFD (use fdisk and set the type to ``fd'')
is confusing because I don't have a choice of fd for partition type. If I
put it in it lets me do it but labels it unknown. Is this correct or am I
doing something wrong?
Here is my dmesg. Any ideas as to why it bombs on startup? If I raidstart
manually everything works fine?
Linux version 2.2.5-15 ([EMAIL PROTECTED]) (gcc version
egcs-2.91.66 1
9990314/Linux (egcs-1.1.2 release)) #1 Mon Apr 19 23:00:46 EDT 1999
Detected 448626242 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 447.28 BogoMIPS
Memory: 192600k/196608k available (996k kernel code, 412k reserved, 2216k data,
60k init)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium II (Deschutes) stepping 02
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.26 (19981001) Richard Gooch ([EMAIL PROTECTED])
PCI: PCI BIOS revision 2.10 entry at 0xfca8e
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9)
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 90845D4, ATA DISK drive
hdc: CRD-8400B, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: Maxtor 90845D4, 8063MB w/512kB Cache, CHS=1027/255/63
hdc: ATAPI 40X CD-ROM drive, 128kB Cache
Uniform CDROM driver Revision: 2.54
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: using high-speed MMX checksum routine
pII_mmx : 1091.946 MB/sec
p5_mmx : 1058.037 MB/sec
8regs : 773.049 MB/sec
32regs : 555.498 MB/sec
using fastest function: pII_mmx (1091.946 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
hda: hda1 hda2 < hda5 hda6 >
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem).
(scsi0) <Adaptec AHA-294X Ultra2 SCSI host adapter> found at PCI 13/0
(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 374 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.15/3.2.4
<Adaptec AHA-294X Ultra2 SCSI host adapter>
scsi : 1 host.
(scsi0:0:1:0) Synchronous at 40.0 Mbyte/sec, offset 31.
Vendor: IBM Model: DNES-318350W Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sda at scsi0, channel 0, id 1, lun 0
(scsi0:0:2:0) Synchronous at 40.0 Mbyte/sec, offset 15.
Vendor: SEAGATE Model: ST318275LW Rev: 0001
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 2, lun 0
(scsi0:0:3:0) Synchronous at 40.0 Mbyte/sec, offset 31.
Vendor: QUANTUM Model: VIKING II 9.1WSE Rev: 4110
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdc at scsi0, channel 0, id 3, lun 0
(scsi0:0:4:0) Synchronous at 40.0 Mbyte/sec, offset 31.
Vendor: QUANTUM Model: VIKING II 9.1WSE Rev: 5520
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdd at scsi0, channel 0, id 4, lun 0
SCSI device sda: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB] [17.5 GB]
sda: unknown partition table
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 35566480 [17366 MB] [17.4 GB]
sdb: unknown partition table
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 17836668 [8709 MB] [8.7 GB]
sdc: sdc1
SCSI device sdd: hdwr sector= 512 bytes. Sectors= 17836668 [8709 MB] [8.7 GB]
sdd: sdd1
autodetecting RAID arrays
(read) sdc1's sb offset: 8915968 [events: 00000002]
(read) sdd1's sb offset: 8915968 [events: 00000002]
autorun ...
considering sdd1 ...
adding sdd1 ...
adding sdc1 ...
created md0
bind<sdc1,1>
bind<sdd1,2>
running: <sdd1><sdc1>
now!
sdd1's event counter: 00000002
sdc1's event counter: 00000002
kmod: failed to exec /sbin/modprobe -s -k md-personality-2, errno = 2
do_md_run() returned -22
unbind<sdd1,1>
export_rdev(sdd1)
unbind<sdc1,0>
export_rdev(sdc1)
md0 stopped.
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 60k freed
Adding Swap: 56192k swap-space (priority -1)
3c59x.c:v0.99H 11/17/98 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/
vortex.html
eth0: 3Com 3c905B Cyclone 100baseTx at 0xdc00, 00:c0:4f:37:39:e1, IRQ 11
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 786d.
MII transceiver found at address 0, status 786d.
Enabling bus-master transmits and whole-frame receives.
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
nfsd_init: initialized fhcache, entries=256
Thanks,
Pat
---------------------------------------------------
Patrick Heath
Network Administrator
Fred Hutchinson Cancer Research Center
1100 Fairview Avenue North, A1-162
Seattle, WA 98109
Email: [EMAIL PROTECTED]
Phone: (206) 667-2000
Fax: (206) 667-6525
---------------------------------------------------
