> kmod: failed to exec /sbin/modprobe -s -k md-personality-2, errno = 2
This is your problem. The standard RedHat initrd doesn't include raid support.
Auto-detection of raid arrays occurs before any filesystems are mounted.
Therefore, the raid module you need to run the array is not available.
You need to rebuild your initrd to include raid support, or rebuild the kernel
to have raid support built-in, rather than as a module. To include raid support
in your initrd, run "mkinitrd --with raid0 2.2.5-15 /boot/initrd", substituting
the appropriate raid-level for raid0, the appropriate kernel version for
2.2.5-15, and the appropriate initrd name for /boot/initrd. If you have changed
the name of your initrd, edit /etc/lilo.conf to point at the new initrd. Run
lilo to point it at the new initrd.
Cheers,
Bruno Prior [EMAIL PROTECTED]
> -----Original Message-----
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED]]On Behalf Of Pat Heath
> Sent: 08 October 1999 17:50
> To: [EMAIL PROTECTED]
> Subject: Raid0
>
>
> I was working on doing the autostart for raid0 and the part where it says:
>
>
> 3. The partition-types of the devices used in the RAID must be set to
> 0xFD (use fdisk and set the type to ``fd'')
>
> is confusing because I don't have a choice of fd for partition type. If I
> put it in it lets me do it but labels it unknown. Is this correct or am I
> doing something wrong?
>
> Here is my dmesg. Any ideas as to why it bombs on startup? If I raidstart
> manually everything works fine?
>
> Linux version 2.2.5-15 ([EMAIL PROTECTED]) (gcc version
> egcs-2.91.66 1
> 9990314/Linux (egcs-1.1.2 release)) #1 Mon Apr 19 23:00:46 EDT 1999
> Detected 448626242 Hz processor.
> Console: colour VGA+ 80x25
> Calibrating delay loop... 447.28 BogoMIPS
> Memory: 192600k/196608k available (996k kernel code, 412k reserved,
> 2216k data,
> 60k init)
> VFS: Diskquotas version dquot_6.4.0 initialized
> CPU: Intel Pentium II (Deschutes) stepping 02
> Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> mtrr: v1.26 (19981001) Richard Gooch ([EMAIL PROTECTED])
> PCI: PCI BIOS revision 2.10 entry at 0xfca8e
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> Linux NET4.0 for Linux 2.2
> Based upon Swansea University Computer Society NET3.039
> NET4: Unix domain sockets 1.0 for Linux NET4.0.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> Initializing RT netlink socket
> Starting kswapd v 1.5
> Detected PS/2 Mouse Port.
> Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> pty: 256 Unix98 ptys configured
> apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9)
> Real Time Clock Driver v1.09
> RAM disk driver initialized: 16 RAM disks of 4096K size
> PIIX4: IDE controller on PCI bus 00 dev 39
> PIIX4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
> hda: Maxtor 90845D4, ATA DISK drive
> hdc: CRD-8400B, ATAPI CDROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: Maxtor 90845D4, 8063MB w/512kB Cache, CHS=1027/255/63
> hdc: ATAPI 40X CD-ROM drive, 128kB Cache
> Uniform CDROM driver Revision: 2.54
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a National Semiconductor PC87306
> md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
> raid5: measuring checksumming speed
> raid5: using high-speed MMX checksum routine
> pII_mmx : 1091.946 MB/sec
> p5_mmx : 1058.037 MB/sec
> 8regs : 773.049 MB/sec
> 32regs : 555.498 MB/sec
> using fastest function: pII_mmx (1091.946 MB/sec)
> scsi : 0 hosts.
> scsi : detected total.
> md.c: sizeof(mdp_super_t) = 4096
> Partition check:
> hda: hda1 hda2 < hda5 hda6 >
> RAMDISK: Compressed image found at block 0
> autodetecting RAID arrays
> autorun ...
> ... autorun DONE.
> VFS: Mounted root (ext2 filesystem).
> (scsi0) <Adaptec AHA-294X Ultra2 SCSI host adapter> found at PCI 13/0
> (scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
> (scsi0) Downloading sequencer code... 374 instructions downloaded
> scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.15/3.2.4
> <Adaptec AHA-294X Ultra2 SCSI host adapter>
> scsi : 1 host.
> (scsi0:0:1:0) Synchronous at 40.0 Mbyte/sec, offset 31.
> Vendor: IBM Model: DNES-318350W Rev: SA30
> Type: Direct-Access ANSI SCSI revision: 03
> Detected scsi disk sda at scsi0, channel 0, id 1, lun 0
> (scsi0:0:2:0) Synchronous at 40.0 Mbyte/sec, offset 15.
> Vendor: SEAGATE Model: ST318275LW Rev: 0001
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sdb at scsi0, channel 0, id 2, lun 0
> (scsi0:0:3:0) Synchronous at 40.0 Mbyte/sec, offset 31.
> Vendor: QUANTUM Model: VIKING II 9.1WSE Rev: 4110
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sdc at scsi0, channel 0, id 3, lun 0
> (scsi0:0:4:0) Synchronous at 40.0 Mbyte/sec, offset 31.
> Vendor: QUANTUM Model: VIKING II 9.1WSE Rev: 5520
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sdd at scsi0, channel 0, id 4, lun 0
> SCSI device sda: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB]
> [17.5 GB]
> sda: unknown partition table
> SCSI device sdb: hdwr sector= 512 bytes. Sectors= 35566480 [17366 MB]
> [17.4 GB]
> sdb: unknown partition table
> SCSI device sdc: hdwr sector= 512 bytes. Sectors= 17836668 [8709 MB] [8.7 GB]
> sdc: sdc1
> SCSI device sdd: hdwr sector= 512 bytes. Sectors= 17836668 [8709 MB] [8.7 GB]
> sdd: sdd1
> autodetecting RAID arrays
> (read) sdc1's sb offset: 8915968 [events: 00000002]
> (read) sdd1's sb offset: 8915968 [events: 00000002]
> autorun ...
> considering sdd1 ...
> adding sdd1 ...
> adding sdc1 ...
> created md0
> bind<sdc1,1>
> bind<sdd1,2>
> running: <sdd1><sdc1>
> now!
> sdd1's event counter: 00000002
> sdc1's event counter: 00000002
> kmod: failed to exec /sbin/modprobe -s -k md-personality-2, errno = 2
> do_md_run() returned -22
> unbind<sdd1,1>
> export_rdev(sdd1)
> unbind<sdc1,0>
> export_rdev(sdc1)
> md0 stopped.
> ... autorun DONE.
> VFS: Mounted root (ext2 filesystem) readonly.
> change_root: old root has d_count=1
> Trying to unmount old root ... okay
> Freeing unused kernel memory: 60k freed
> Adding Swap: 56192k swap-space (priority -1)
> 3c59x.c:v0.99H 11/17/98 Donald Becker
> http://cesdis.gsfc.nasa.gov/linux/drivers/
> vortex.html
> eth0: 3Com 3c905B Cyclone 100baseTx at 0xdc00, 00:c0:4f:37:39:e1, IRQ 11
> 8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
> MII transceiver found at address 24, status 786d.
> MII transceiver found at address 0, status 786d.
> Enabling bus-master transmits and whole-frame receives.
> Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
> nfsd_init: initialized fhcache, entries=256
>
> Thanks,
> Pat
>
>
>
> ---------------------------------------------------
> Patrick Heath
> Network Administrator
> Fred Hutchinson Cancer Research Center
> 1100 Fairview Avenue North, A1-162
> Seattle, WA 98109
>
> Email: [EMAIL PROTECTED]
> Phone: (206) 667-2000
> Fax: (206) 667-6525
> ---------------------------------------------------
>
>
>
>
