Hi,
I checked all termination things, cable etc. again and again. I am doing this
for years now and would be very happy to find the problem at my end.
I doubt that there is the problem. At the moment I am using an (active?) AMP
-Terminator, but I also tried to terminate directly at the CDROM, which is
pretty easy.
The most important fact to me is that with exactly the same HW-Setup the
installation of RH6.0 works, but RH6.1 fails.
Below I atttached a few details from the current RH6.0 installation.
In about an hour I'll try to install RH6.1 again from scratch with exact the
same HW-Setup and hope I can post as much as possible information to you.
Regards,
Mario
--
Mario Dix / Kirsteinstrasse 54A / 12559 Berlin / Germany / Tel +49 30 65908113
--uptime--------------------------------
6:37pm up 2 days, 21:18, 4 users, load average: 0.00, 0.00, 0.00
----dmesg----------------------------------
Linux version 2.2.9-2 ([EMAIL PROTECTED]) (gcc version egcs-2.91.66 19990314/Linux
(egcs-1.1.2 release)) #1 Sam Mai 29 23:08:41 CEST 1999
Detected 400919882 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 799.54 BogoMIPS
Memory: 257472k/262080k available (980k kernel code, 408k reserved, 2844k data, 60k
init)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: AMD AMD-K6(tm) 3D processor stepping 0c
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.34 (19990310) Richard Gooch ([EMAIL PROTECTED])
PCI: PCI BIOS revision 2.10 entry at 0xfb490
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: 00:38 [1106/0586]: Work around ISA DMA hangs (00)
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.9)
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: placing both ports into native PCI mode
VP_IDE: Missing I/O address #0, please report to <[EMAIL PROTECTED]>
VP_IDE: device disabled (BIOS)
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
scsi : 0 hosts.
scsi : detected total.
Partition check:
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
ncr53c8xx: at PCI bus 0, device 8, function 0
ncr53c8xx: 53c875 detected with Symbios NVRAM
ncr53c875-0: rev=0x04, base=0xec002000, io_port=0xd800, irq=15
ncr53c875-0: Symbios format NVRAM, ID 7, Fast-20, Parity Checking
ncr53c875-0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/4e/80/01/00/24
ncr53c875-0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/46/a0/00/08/24
ncr53c875-0: on-chip RAM at 0xec001000
ncr53c875-0: resetting, command processing suspended for 2 seconds
ncr53c875-0: restart (scsi reset).
ncr53c875-0: enabling clock multiplier
ncr53c875-0: Downloading SCSI SCRIPTS.
scsi0 : ncr53c8xx - version 3.2
scsi : 1 host.
ncr53c875-0: command processing resumed
Vendor: TOSHIBA Model: CD-ROM XM-3601TA Rev: 0265
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
ncr53c875-0-<5,*>: FAST-5 SCSI 4.0 MB/s (250 ns, offset 16)
sr0: scsi3-mmc drive: 0x/0x caddy
Uniform CDROM driver Revision: 2.55
EATA (Extended Attachment) driver version: 2.59b
developed in co-operation with DPT
(c) 1993-96 Michael Neuffer, [EMAIL PROTECTED]
Registered HBAs:
HBA no. Boardtype Revis EATA Bus BaseIO IRQ DMA Ch ID Pr QS S/G IS
scsi1 : PM3334UW v07M.0 2.0c PCI 0xe010 10 BMST 2 7 N 64 252 Y
scsi1 : EATA (Extended Attachment) HBA driver
scsi : 2 hosts.
Vendor: DPT Model: RAID-A Rev: 07M0
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi1, channel 0, id 1, lun 0
Vendor: DPT Model: RAID-B Rev: 07M0
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi1, channel 1, id 0, lun 0
scsi1: queue depth for target 1 on channel 0 set to 32
scsi1: queue depth for target 0 on channel 1 set to 32
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17915728 [8747 MB] [8.7 GB]
sda: sda1 sda2 sda3 sda4
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17915728 [8747 MB] [8.7 GB]
sdb: sdb1 sdb2 sdb3 sdb4
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 60k freed
Adding Swap: 521724k swap-space (priority -1)
tulip.c:v0.89H 5/23/98 [EMAIL PROTECTED]
eth0: Digital DS21140 Tulip at 0xdc00, 00 80 c8 94 41 a8, IRQ 11.
eth0: EEPROM default media type Autosense.
eth0: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block.
eth0: MII transceiver found at MDIO address 0, config 1000 status 782d.
eth0: Advertising 01e1 on PHY 0, previously advertising 01e1.
eth0: Advertising 01e1 on PHY 0 (0).
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
nfsd_init: initialized fhcache, entries=256
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
SB 4.16 detected OK (220)
<SoundBlaster EMU8000 (RAM512k)>
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
SB 4.16 detected OK (220)
<SoundBlaster EMU8000 (RAM512k)>
VFS: Disk change detected on device sr(11,0)
VFS: Disk change detected on device sr(11,0)
sr0: CDROM not ready. Make sure there is a disc in the drive.
sr0: CDROM not ready. Make sure there is a disc in the drive.
sr0: CDROM not ready. Make sure there is a disc in the drive.
sr0: CDROM not ready. Make sure there is a disc in the drive.
kcminfo uses obsolete /proc/pci interface
eata_dma: int_handler, board: e010 cmd c0f0cad8 returned unfinished.
EATA: 51 HBA: 0 SCSI: 0 spadr d0015630 spadrirq c0f1aef0, irq10
parport0: PC-style at 0x378 [SPP,PS2,EPP]
parport0: Printer, Canon LBP-1760
lp0: using parport0 (polling).
lp0: using parport0 (polling).
parport0: PC-style at 0x378 [SPP,PS2,EPP]
parport0: Printer, Canon LBP-1760
lp0: using parport0 (polling).
----lsmod----------------------
Module Size Used by
awe_wave 157132 0
sb 33076 0
uart401 5936 0 [sb]
sound 58392 0 [awe_wave sb uart401]
soundlow 300 0 [sound]
soundcore 2404 7 [sb sound]
nfsd 151160 8 (autoclean)
lockd 31208 1 (autoclean) [nfsd]
sunrpc 52612 1 (autoclean) [nfsd lockd]
tulip 24740 1 (autoclean)
nls_iso8859-1 2020 1 (autoclean)
nls_cp437 3548 1 (autoclean)
vfat 11196 1 (autoclean)
fat 25344 1 (autoclean) [vfat]
eata_dma 23872 8
ncr53c8xx 51560 0
--------/proc/pci---------------
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: VIA Technologies VT 82C597 Apollo VP3 (rev 4).
Medium devsel. Fast back-to-back capable. Master Capable. Latency=16.
Prefetchable 32 bit memory at 0xe0000000 [0xe0000008].
Bus 0, device 1, function 0:
PCI bridge: VIA Technologies VT 82C598 Apollo MVP3 AGP (rev 0).
Medium devsel. Master Capable. No bursts. Min Gnt=12.
Bus 0, device 7, function 0:
ISA bridge: VIA Technologies VT 82C586 Apollo ISA (rev 65).
Medium devsel. Master Capable. No bursts.
Bus 0, device 7, function 1:
IDE interface: VIA Technologies VT 82C586 Apollo IDE (rev 6).
Medium devsel. Fast back-to-back capable. Master Capable. Latency=64.
I/O at 0xd000 [0xd001].
Bus 0, device 8, function 0:
SCSI storage controller: NCR 53c875 (rev 4).
Medium devsel. IRQ 15. Master Capable. Latency=72. Min Gnt=17.Max Lat=64.
I/O at 0xd800 [0xd801].
Non-prefetchable 32 bit memory at 0xec002000 [0xec002000].
Non-prefetchable 32 bit memory at 0xec001000 [0xec001000].
Bus 0, device 9, function 0:
Ethernet controller: DEC DC21140 (rev 34).
Medium devsel. Fast back-to-back capable. IRQ 11. Master Capable.
Latency=64. Min Gnt=20.Max Lat=40.
I/O at 0xdc00 [0xdc01].
Non-prefetchable 32 bit memory at 0xec000000 [0xec000000].
Bus 0, device 10, function 0:
SCSI storage controller: DPT SmartCache/Raid (rev 2).
Medium devsel. BIST capable. IRQ 10. Master Capable. Latency=64. Min
Gnt=4.Max Lat=8.
I/O at 0xe000 [0xe001].
Bus 1, device 0, function 0:
VGA compatible controller: Matrox Matrox G200 AGP (rev 1).
Medium devsel. Fast back-to-back capable. Master Capable. Latency=64. Min
Gnt=16.Max Lat=32.
Prefetchable 32 bit memory at 0xe8000000 [0xe8000008].
Non-prefetchable 32 bit memory at 0xe4000000 [0xe4000000].
Non-prefetchable 32 bit memory at 0xe5000000 [0xe5000000].
---/proc/scsi/ncr53c8xx/0 --------------------------------
General information:
Chip NCR53C875, device id 0xf, revision id 0x4
IO port address 0xd800, IRQ number 15
Using memory mapped IO at virtual address 0xd000e000
Synchronous period factor 12, max commands per lun 32
Profiling information:
num_trans = 27
num_kbytes = 4
num_disc = 0
num_break = 1
num_int = 53
num_fly = 27
ms_setup = 70
ms_data = 80
ms_disc = 0
ms_post = 0
---/proc/scsi/eata_dma/1 ---------------------
EATA (Extended Attachment) driver version: 2.59b
queued commands: 135409
processed interrupts: 135116
scsi1 : HBA PM3334UW
Firmware revision: v07M.0
Hardware Configuration:
IRQ: 0, edge triggered
DMA: BUSMASTER
CPU: MC68000 0MHz
Base IO : 0xe010
Host Bus: PCI
SCSI Bus: Speed: 5MB/sec.
SCSI channel expansion Module: not present
SmartRAID hardware: not present.
Type: -
Max array groups: 7
Max drives per RAID 0 array: 7
Max drives per RAID 3/5 array: 7
Cache Module: not present.
Type: -
Bank0: 0MB without ECC
Bank1: 0MB without ECC
Bank2: 0MB without ECC
Bank3: 0MB without ECC
Timer Mod.: not present
NVRAM : not present
SmartROM : enabled
Alarm : off
Host<->Disk command statistics:
Reads: Writes:
1k: 0 0
2k: 0 0
4k: 0 0
8k: 0 0
16k: 0 0
32k: 0 0
64k: 0 0
128k: 0 0
256k: 0 0
512k: 0 0
1024k: 0 0
>1024k: 0 0
Sum : 0 0
Attached devices:
Host: scsi1 Channel: 00 Id: 01 Lun: 00
Vendor: DPT Model: RAID-A Rev: 07M0
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 01 Id: 00 Lun: 00
Vendor: DPT Model: RAID-B Rev: 07M0
Type: Direct-Access ANSI SCSI revision: 02
