On Fri, Sep 18, 2015 at 4:48 PM, Maxime Ripard <maxime.rip...@free-electrons.com> wrote: > The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of > RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack > and two connectors to plug additional boards on top of it. > > Signed-off-by: Maxime Ripard <maxime.rip...@free-electrons.com> > --- > arch/arm/boot/dts/Makefile | 3 +- > arch/arm/boot/dts/sun5i-r8-chip.dts | 261 > ++++++++++++++++++++++++++++++++++++ > 2 files changed, 263 insertions(+), 1 deletion(-) > create mode 100644 arch/arm/boot/dts/sun5i-r8-chip.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index b276174b670a..7efd37b907f1 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -599,7 +599,8 @@ dtb-$(CONFIG_MACH_SUN5I) += \ > sun5i-a13-inet-98v-rev2.dtb \ > sun5i-a13-olinuxino.dtb \ > sun5i-a13-olinuxino-micro.dtb \ > - sun5i-a13-utoo-p66.dtb > + sun5i-a13-utoo-p66.dtb \ > + sun5i-r8-chip.dtb > dtb-$(CONFIG_MACH_SUN6I) += \ > sun6i-a31-app4-evb1.dtb \ > sun6i-a31-colombus.dtb \ > diff --git a/arch/arm/boot/dts/sun5i-r8-chip.dts > b/arch/arm/boot/dts/sun5i-r8-chip.dts > new file mode 100644 > index 000000000000..6cb3c4f1cd61 > --- /dev/null > +++ b/arch/arm/boot/dts/sun5i-r8-chip.dts > @@ -0,0 +1,261 @@ > +/* > + * Copyright 2015 Free Electrons > + * Copyright 2015 NextThing Co > + * > + * Maxime Ripard <maxime.rip...@free-electrons.com> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +/dts-v1/; > +#include "sun5i-a13.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/irq.h> > + > +/ { > + model = "NextThing C.H.I.P."; > + compatible = "nextthing,chip", "allwinner,sun5i-r8"; > + > + aliases { > + i2c0 = &i2c0; > + i2c1 = &i2c1; > + i2c2 = &i2c2; > + serial0 = &uart1; > + serial1 = &uart3; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + dram_vcc: dram_vcc { > + compatible = "regulator-fixed"; > + regulator-name = "dram-vcc"; > + regulator-min-microvolt = <1600000>; > + regulator-max-microvolt = <1600000>; > + vin-supply = <&ipsout>; > + regulator-always-on; > + };
Do we need this if it's not controllable? > + > + ipsout: ipsout { > + compatible = "regulator-fixed"; > + regulator-name = "ipsout"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; This isn't needed. What we might want is a proper representation of the AXP209's power supply. > + > + usb0_vbus: usb0_vbus { > + compatible = "regulator-fixed"; > + pinctrl-names = "default"; > + pinctrl-0 = <&chip_vbus_pin>; > + > + regulator-name = "vbus-usb0"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <&vcc_5v0>; > + gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>; /* PB10 */ > + enable-active-high; > + }; > + > + vcc_3v3: vcc3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "vcc-3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&ipsout>; > + regulator-always-on; > + }; > + > + vcc_5v0: vcc5v0 { > + compatible = "regulator-fixed"; > + regulator-name = "vcc-5v0"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <&ipsout>; > + regulator-always-on; > + }; We have these in sunxi-common-regulators.dtsi. > +}; > + > +&ehci0 { > + status = "okay"; > +}; > + > +&i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c0_pins_a>; > + status = "okay"; > + > + axp209: pmic@34 { > + reg = <0x34>; > + > + /* > + * The interrupt is routed through the "External Fast > + * Interrupt Request" pin (ball G13 of the module) > + * directly to the main interrupt controller, without > + * any other controller interfering. > + */ > + interrupts = <0>; > + }; > +}; > + > +#include "axp209.dtsi" > + > +/* > + * i2c1 is routed to the external pins and doesn't have any device > + * attached to it on the C.H.I.P itself. > + */ > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins_a>; > + status = "okay"; > +}; > + > +&i2c2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c2_pins_a>; > + status = "okay"; > + > + xio: gpio@38 { > + compatible = "nxp,pcf8574a"; > + reg = <0x38>; > + > + gpio-controller; > + #gpio-cells = <2>; > + > + interrupt-parent = <&pio>; > + interrupts = <6 0 IRQ_TYPE_EDGE_FALLING>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > +}; > + > +&mmc0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc0_pins_a>; > + vmmc-supply = <&vcc_3v3>; > + bus-width = <4>; > + non-removable; > + status = "okay"; > +}; > + > +&ohci0 { > + status = "okay"; > +}; > + > +&otg_sram { > + status = "okay"; > +}; > + > +&pio { > + chip_vbus_pin: chip_vbus_pin@0 { > + allwinner,pins = "PB10"; > + allwinner,function = "gpio_out"; > + allwinner,drive = <SUN4I_PINCTRL_10_MA>; > + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; > + }; > + > + chip_id_det_pin: chip_id_det_pin@0 { > + allwinner,pins = "PG2"; > + allwinner,function = "gpio_in"; > + allwinner,drive = <SUN4I_PINCTRL_10_MA>; > + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; > + }; > +}; > + > +®_dcdc2 { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1400000>; > + regulator-name = "cpuvdd"; > + regulator-always-on; > +}; > + > +®_dcdc3 { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1300000>; > + regulator-name = "corevdd"; > + regulator-always-on; > +}; > + > +®_ldo1 { > + regulator-name = "rtcvdd"; > +}; > + > +®_ldo2 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <3300000>; Maybe just fix this to 3.0V? > + regulator-name = "avcc"; > + regulator-always-on; > +}; > + > +®_ldo5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-1v8"; A comment here saying this is found on the header, and to be used by overlays would be nice. > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart1_pins_b>; > + status = "okay"; > +}; > + > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart3_pins_a>, > + <&uart3_pins_cts_rts_a>; > + status = "okay"; > +}; > + > +&usb_otg { > + dr_mode = "otg"; > + status = "okay"; > +}; > + > +&usbphy { > + pinctrl-names = "default"; > + pinctrl-0 = <&chip_id_det_pin>; > + status = "okay"; > + > + usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */ Better leave a comment here saying VBUS detection requires AXP209 usb-power-supply support. > + > + usb0_vbus-supply = <&usb0_vbus>; > + usb1_vbus-supply = <&vcc_5v0>; > +}; > -- > 2.5.1 > Thanks! ChenYu -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.