I think i'm attached this files on 18.1.2006., but here it again.
I'm sorry about wrong naming convention.
There is few different situation. Hub, Usb Audio is on Port2, Camera on Port4,
everything is connected together when system booting.
Aleksancar Loncar.
> > I forgot to say. When system is booted and when I adding one by one
device
> everything work fine, recognition is 100% accurate and all working.
> > Aleksandar Loncar.
>
> Turn on CONFIG_USB_DEBUG and post the dmesg log showing what happens
> during boot when your system fails to recognize a device.
>
> Alan Stern
ndalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 4ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
sa1111-ohci 0400: created debug files
hub 1-0:1.0: state 5 ports 1 chg 0002 evt 0003
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 1-1: new full speed USB device using sa1111-ohci and address 2
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 1-1: ep0 maxpacket = 8
usb 1-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1: default language 0x0409
usb 1-1: Product: USB Hub
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
hub 1-1:1.0: usb_probe_interface
hub 1-1:1.0: usb_probe_interface - got id
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
hub 1-1:1.0: standalone hub
hub 1-1:1.0: individual port power switching
hub 1-1:1.0: individual port over-current protection
hub 1-1:1.0: power on to power good time: 100ms
hub 1-1:1.0: local power source is good
hub 1-1:1.0: enabling power on all ports
hub 1-0:1.0: state 5 ports 1 chg 0000 evt 0002
hub 1-1:1.0: state 5 ports 4 chg 001e evt 001f
hub 1-1:1.0: port 1, status 0100, change 0000, 12 Mb/s
hub 1-1:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-1:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
usb 1-1.2: new full speed USB device using sa1111-ohci and address 3
usb 1-1.2: ep0 maxpacket = 8
usb 1-1.2: skipped 4 descriptors after interface
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: new device strings: Mfr=0, Product=0, SerialNumber=1
usb 1-1.2: default language 0x0409
usb 1-1.2: SerialNumber: 021202105AF8590D
usb 1-1.2: hotplug
usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
usb 1-1.2:1.0: hotplug
usb 1-1.2: adding 1-1.2:1.1 (config #1, interface 1)
usb 1-1.2:1.1: hotplug
usb 1-1.2: adding 1-1.2:1.2 (config #1, interface 2)
usb 1-1.2:1.2: hotplug
hub 1-1:1.0: port 3, status 0100, change 0000, 12 Mb/s
hub 1-1:1.0: port 4, status 0101, change 0001, 12 Mb/s
Linux video capture interface: v1.00
hub 1-1:1.0: debounce: port 4: total 100ms stable 100ms status 0x101
usb 1-1.4: new full speed USB device using sa1111-ohci and address 4
usb 1-1.4: ep0 maxpacket = 8
usb 1-1.4: skipped 11 descriptors after interface
usb 1-1.4: skipped 2 descriptors after interface
usb 1-1.4: skipped 1 descriptor after endpoint
usb 1-1.4: skipped 2 descriptors after interface
usb 1-1.4: skipped 1 descriptor after endpoint
usb 1-1.4: skipped 2 descriptors after interface
usb 1-1.4: skipped 1 descriptor after endpoint
usb 1-1.4: skipped 2 descriptors after interface
usb 1-1.4: skipped 1 descriptor after endpoint
usb 1-1.4: skipped 2 descriptors after interface
usb 1-1.4: skipped 1 descriptor after endpoint
usb 1-1.4: skipped 1 descriptor after interface
usb 1-1.4: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.4: default language 0x0409
usb 1-1.4: Product: UAC3556B
usb 1-1.4: Manufacturer: Micronas
usb 1-1.4: hotplug
usb 1-1.4: adding 1-1.4:1.0 (config #1, interface 0)
usb 1-1.4:1.0: hotplug
usb 1-1.4: adding 1-1.4:1.1 (config #1, interface 1)
usb 1-1.4:1.1: hotplug
usb 1-1.4: adding 1-1.4:1.2 (config #1, interface 2)
usb 1-1.4:1.2: hotplug
usb 1-1.4: adding 1-1.4:1.3 (config #1, interface 3)
usb 1-1.4:1.3: hotplug
hub 1-1:1.0: state 5 ports 4 chg 0000 evt 0010
pwc Philips webcam module version 10.0.9-unofficial loaded.
pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 &
PCVC830/840.
pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10
and MPC-C30,
pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and
VCS-UM100.
pwc Trace options: 0x00a1
Philips webcam 1-1.2:1.0: usb_probe_interface
Philips webcam 1-1.2:1.0: usb_probe_interface - got id
pwc Samsung MPC-C10 USB webcam detected.
pwc Registered as /dev/video0.
Philips webcam 1-1.2:1.1: usb_probe_interface
Philips webcam 1-1.2:1.1: usb_probe_interface - got id
Philips webcam 1-1.2:1.2: usb_probe_interface
Philips webcam 1-1.2:1.2: usb_probe_interface - got id
usbcore: registered new driver Philips webcam
audio 1-1.2:1.1: usb_probe_interface
audio 1-1.2:1.1: usb_probe_interface - got id
usbaudio: device 3 audiocontrol interface 1 has 1 input and 0 output
AudioStreaming interfaces
usbaudio: device 3 interface 2 altsetting 0 FORMAT_TYPE descriptor not found
usbaudio: valid input sample rate 44100
usbaudio: device 3 interface 2 altsetting 1: format 0x00000010 sratelo 44100
sratehi 44100 attributes 0x00
usbaudio: valid input sample rate 22050
usbaudio: device 3 interface 2 altsetting 2: format 0x00000010 sratelo 22050
sratehi 22050 attributes 0x00
usbaudio: valid input sample rate 11025
usbaudio: device 3 interface 2 altsetting 3: format 0x00000010 sratelo 11025
sratehi 11025 attributes 0x00
usbaudio: valid input sample rate 8000
usbaudio: device 3 interface 2 altsetting 4: format 0x00000010 sratelo 8000
sratehi 8000 attributes 0x00
usbaudio: registered dsp 14,3
usbaudio: constructing mixer for Terminal 3 type 0x0101
usbaudio: warning: found 1 of 0 logical channels.
usbaudio: assuming the channel found is the master channel (got a Philips
camera?). Should be fine.
usbaudio: registered mixer 14,0
usb_audio_parsecontrol: usb_audio_state at c3c7dc40
audio 1-1.4:1.0: usb_probe_interface
audio 1-1.4:1.0: usb_probe_interface - got id
usbaudio: device 4 audiocontrol interface 0 has 1 input and 1 output
AudioStreaming interfaces
usbaudio: valid input sample rate 6400
usbaudio: valid input sample rate 48000
usbaudio: device 4 interface 2 altsetting 1: format 0x00000040 sratelo 6400
sratehi 48000 attributes 0x01
usbaudio: valid input sample rate 6400
usbaudio: valid input sample rate 48000
usbaudio: device 4 interface 2 altsetting 2: format 0x00000010 sratelo 6400
sratehi 48000 attributes 0x01
usbaudio: valid input sample rate 6400
usbaudio: valid input sample rate 48000
usbaudio: device 4 interface 2 altsetting 3: format 0x80000010 sratelo 6400
sratehi 48000 attributes 0x01
usbaudio: valid output sample rate 6400
usbaudio: valid output sample rate 48000
usbaudio: device 4 interface 1 altsetting 1: format 0x00000010 sratelo 6400
sratehi 48000 attributes 0x01
usbaudio: valid output sample rate 6400
usbaudio: valid output sample rate 48000
usbaudio: device 4 interface 1 altsetting 2: format 0x80000010 sratelo 6400
sratehi 48000 attributes 0x01
usbaudio: registered dsp 14,19
usbaudio: constructing mixer for Terminal 20 type 0x0301
usbaudio: registered mixer 14,16
usbaudio: constructing mixer for Terminal 13 type 0x0101
usbaudio: registered mixer 14,32
usb_audio_parsecontrol: usb_audio_state at c2c37820
usbcore: registered new driver audio
drivers/usb/class/audio.c: v1.0.0:USB Audio Class driver
usbcore: registered new driver hiddev
usbhid 1-1.4:1.3: usb_probe_interface
usbhid 1-1.4:1.3: usb_probe_interface - got id
evbug.c: Connected device: "Micronas UAC3556B", usb-sa1111-1.4/input3
input: USB HID v1.00 Device [Micronas UAC3556B] on usb-sa1111-1.4
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usbcore: registered new driver usbfs
usbcore: registered new driver hub
drivers/usb/host/ohci-sa1111.c: 2004 Nov 08 USB 1.1 'Open' Host Controller
(OHCI) Driver (SA-1111)
drivers/usb/host/ohci-sa1111.c: block sizes: ed 64 td 64
drivers/usb/host/ohci-sa1111.c: starting SA-1111 OHCI USB Controller
drivers/usb/host/ohci-sa1111.c: ohci_hcd (SA-1111) at 0xc4800400, irq 164
sa1111-ohci 0400: new USB bus registered, assigned bus number 1
sa1111-ohci 0400: resetting from state 'reset', control = 0x0
sa1111-ohci 0400: OHCI controller state
sa1111-ohci 0400: OHCI 1.0, with legacy support registers
sa1111-ohci 0400: control 0x083 HCFS=operational CBSR=3
sa1111-ohci 0400: cmdstatus 0x00000 SOC=0
sa1111-ohci 0400: intrstatus 0x00000044 RHSC SF
sa1111-ohci 0400: intrenable 0x8000001a MIE UE RD WDH
sa1111-ohci 0400: hcca frame #0005
sa1111-ohci 0400: roothub.a 02000201 POTPGT=2 NPS NDP=1
sa1111-ohci 0400: roothub.b 00000000 PPCM=0000 DR=0000
sa1111-ohci 0400: roothub.status 00008000 DRWE
sa1111-ohci 0400: roothub.portstatus [0] 0x00010101 CSC PPS CCS
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: SA-1111 OHCI
usb usb1: Manufacturer: Linux 2.6.11-sg1 ohci_hcd
usb usb1: SerialNumber: sa1111
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 4ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
sa1111-ohci 0400: created debug files
hub 1-0:1.0: state 5 ports 1 chg 0002 evt 0003
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 1-1: new full speed USB device using sa1111-ohci and address 2
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 1-1: ep0 maxpacket = 8
usb 1-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1: default language 0x0409
usb 1-1: Product: USB Hub
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
hub 1-1:1.0: usb_probe_interface
hub 1-1:1.0: usb_probe_interface - got id
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
hub 1-1:1.0: standalone hub
hub 1-1:1.0: individual port power switching
hub 1-1:1.0: individual port over-current protection
hub 1-1:1.0: power on to power good time: 100ms
hub 1-1:1.0: local power source is good
hub 1-1:1.0: enabling power on all ports
hub 1-0:1.0: state 5 ports 1 chg 0000 evt 0002
hub 1-1:1.0: state 5 ports 4 chg 001e evt 001f
hub 1-1:1.0: port 1, status 0100, change 0000, 12 Mb/s
hub 1-1:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-1:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
usb 1-1.2: new full speed USB device using sa1111-ohci and address 3
usb 1-1.2: ep0 maxpacket = 8
usb 1-1.2: skipped 4 descriptors after interface
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: new device strings: Mfr=0, Product=0, SerialNumber=1
usb 1-1.2: default language 0x0409
usb 1-1.2: SerialNumber: 021202105AF8590D
usb 1-1.2: hotplug
usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
usb 1-1.2:1.0: hotplug
usb 1-1.2: adding 1-1.2:1.1 (config #1, interface 1)
usb 1-1.2:1.1: hotplug
usb 1-1.2: adding 1-1.2:1.2 (config #1, interface 2)
usb 1-1.2:1.2: hotplug
Linux video capture interface: v1.00
pwc Philips webcam module version 10.0.9-unofficial loaded.
pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 &
PCVC830/840.
pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10
and MPC-C30,
pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and
VCS-UM100.
pwc Trace options: 0x00a1
usbcore: registered new driver usbfs
usbcore: registered new driver hub
drivers/usb/host/ohci-sa1111.c: 2004 Nov 08 USB 1.1 'Open' Host Controller
(OHCI) Driver (SA-1111)
drivers/usb/host/ohci-sa1111.c: block sizes: ed 64 td 64
drivers/usb/host/ohci-sa1111.c: starting SA-1111 OHCI USB Controller
drivers/usb/host/ohci-sa1111.c: ohci_hcd (SA-1111) at 0xc4800400, irq 164
sa1111-ohci 0400: new USB bus registered, assigned bus number 1
sa1111-ohci 0400: resetting from state 'reset', control = 0x0
sa1111-ohci 0400: OHCI controller state
sa1111-ohci 0400: OHCI 1.0, with legacy support registers
sa1111-ohci 0400: control 0x083 HCFS=operational CBSR=3
sa1111-ohci 0400: cmdstatus 0x00000 SOC=0
sa1111-ohci 0400: intrstatus 0x00000044 RHSC SF
sa1111-ohci 0400: intrenable 0x8000001a MIE UE RD WDH
sa1111-ohci 0400: hcca frame #0005
sa1111-ohci 0400: roothub.a 02000201 POTPGT=2 NPS NDP=1
sa1111-ohci 0400: roothub.b 00000000 PPCM=0000 DR=0000
sa1111-ohci 0400: roothub.status 00008000 DRWE
sa1111-ohci 0400: roothub.portstatus [0] 0x00010101 CSC PPS CCS
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: SA-1111 OHCI
usb usb1: Manufacturer: Linux 2.6.11-sg1 ohci_hcd
usb usb1: SerialNumber: sa1111
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 4ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
sa1111-ohci 0400: created debug files
hub 1-0:1.0: state 5 ports 1 chg 0002 evt 0003
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 1-1: new full speed USB device using sa1111-ohci and address 2
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 1-1: ep0 maxpacket = 8
usb 1-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1: default language 0x0409
usb 1-1: Product: USB Hub
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
hub 1-1:1.0: usb_probe_interface
hub 1-1:1.0: usb_probe_interface - got id
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
hub 1-1:1.0: standalone hub
hub 1-1:1.0: individual port power switching
hub 1-1:1.0: individual port over-current protection
hub 1-1:1.0: power on to power good time: 100ms
hub 1-1:1.0: local power source is good
hub 1-1:1.0: enabling power on all ports
hub 1-0:1.0: state 5 ports 1 chg 0000 evt 0002
hub 1-1:1.0: state 5 ports 4 chg 001e evt 001f
hub 1-1:1.0: port 1, status 0100, change 0000, 12 Mb/s
hub 1-1:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-1:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
usb 1-1.2: new full speed USB device using sa1111-ohci and address 3
usbcore: registered new driver usbfs
usbcore: registered new driver hub
drivers/usb/host/ohci-sa1111.c: 2004 Nov 08 USB 1.1 'Open' Host Controller
(OHCI) Driver (SA-1111)
drivers/usb/host/ohci-sa1111.c: block sizes: ed 64 td 64
drivers/usb/host/ohci-sa1111.c: starting SA-1111 OHCI USB Controller
drivers/usb/host/ohci-sa1111.c: ohci_hcd (SA-1111) at 0xc4800400, irq 164
sa1111-ohci 0400: new USB bus registered, assigned bus number 1
sa1111-ohci 0400: resetting from state 'reset', control = 0x0
sa1111-ohci 0400: OHCI controller state
sa1111-ohci 0400: OHCI 1.0, with legacy support registers
sa1111-ohci 0400: control 0x083 HCFS=operational CBSR=3
sa1111-ohci 0400: cmdstatus 0x00000 SOC=0
sa1111-ohci 0400: intrstatus 0x00000044 RHSC SF
sa1111-ohci 0400: intrenable 0x8000001a MIE UE RD WDH
sa1111-ohci 0400: hcca frame #0005
sa1111-ohci 0400: roothub.a 02000201 POTPGT=2 NPS NDP=1
sa1111-ohci 0400: roothub.b 00000000 PPCM=0000 DR=0000
sa1111-ohci 0400: roothub.status 00008000 DRWE
sa1111-ohci 0400: roothub.portstatus [0] 0x00010101 CSC PPS CCS
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: SA-1111 OHCI
usb usb1: Manufacturer: Linux 2.6.11-sg1 ohci_hcd
usb usb1: SerialNumber: sa1111
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 4ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
sa1111-ohci 0400: created debug files
hub 1-0:1.0: state 5 ports 1 chg 0002 evt 0003
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 1-1: new full speed USB device using sa1111-ohci and address 2
sa1111-ohci 0400: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 1-1: ep0 maxpacket = 8
usb 1-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1: default language 0x0409
usb 1-1: Product: USB Hub
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
hub 1-1:1.0: usb_probe_interface
hub 1-1:1.0: usb_probe_interface - got id
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
hub 1-1:1.0: standalone hub
hub 1-1:1.0: individual port power switching
hub 1-1:1.0: individual port over-current protection
hub 1-1:1.0: power on to power good time: 100ms
hub 1-1:1.0: local power source is good
hub 1-1:1.0: enabling power on all ports
hub 1-0:1.0: state 5 ports 1 chg 0000 evt 0002
hub 1-1:1.0: state 5 ports 4 chg 001e evt 001f
hub 1-1:1.0: port 1, status 0100, change 0000, 12 Mb/s
hub 1-1:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-1:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
usb 1-1.2: new full speed USB device using sa1111-ohci and address 3
usb 1-1.2: ep0 maxpacket = 8
usb 1-1.2: skipped 4 descriptors after interface
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: skipped 2 descriptors after interface
usb 1-1.2: skipped 1 descriptor after endpoint
usb 1-1.2: new device strings: Mfr=0, Product=0, SerialNumber=1
usb 1-1.2: default language 0x0409
usb 1-1.2: SerialNumber: 021202105AF8590D
usb 1-1.2: hotplug
usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
usb 1-1.2:1.0: hotplug
usb 1-1.2: adding 1-1.2:1.1 (config #1, interface 1)
usb 1-1.2:1.1: hotplug
usb 1-1.2: adding 1-1.2:1.2 (config #1, interface 2)
usb 1-1.2:1.2: hotplug
hub 1-1:1.0: port 3, status 0100, change 0000, 12 Mb/s
hub 1-1:1.0: port 4, status 0101, change 0001, 12 Mb/s
Linux video capture interface: v1.00
hub 1-1:1.0: debounce: port 4: total 100ms stable 100ms status 0x101
usb 1-1.4: new full speed USB device using sa1111-ohci and address 4
pwc Philips webcam module version 10.0.9-unofficial loaded.
pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 &
PCVC830/840.
pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10
and MPC-C30,
pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and
VCS-UM100.
pwc Trace options: 0x00a1
